Question about Hyundai Cars & Trucks

2 Answers

How do you remove the IX35 front skid plate covering the sump

Posted by arthur livock on

Ad

2 Answers

James Mac Intosh

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 38 Answers

There are quite a lot of bolts/screws involved. If memory serves correct, there are a whole handful of torx screws along the perimeter of the belly pan as well as I think either 10mm or 12mm bolts. I think there are about 2/3 at the back (towards the rear of the vehicle) and another few at the front.
I cannot remember if there are those plastic screw type grommets as well but Hyundai are rather fond of them lately

Posted on Mar 01, 2019

Ad

Derrick Schultz

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 11,405 Answers

Hello
u'd need a proper manual for this in my opinion
like there are plenty of dealers and online shops that deal in those..
you can get some free at reliable-store and it;s actually really illustrative

Posted on Feb 07, 2019

Ad

5 Related Answers

Anonymous

  • 27 Answers

SOURCE: Replace the face skid in the front bumper

remove front bumper and it should be clear what holding the face skid in place

Posted on Nov 07, 2008

Kris Suit

  • 85 Answers

SOURCE: Replacing the skid plate on 07 Tahoe Z71

Remove bumper or use a swivel adapter to remove

Posted on Apr 29, 2009

Magaiver

keith macisaac

  • 707 Answers

SOURCE: On a 2004 Jeep Grand Cherokee 4x4 with a 4.7 H.O.

Not as far as i know. But if u can't get it from top or bottom the skid plate is an easy removal. Hope this helps.

Posted on Aug 11, 2010

cy schousboe

  • 2002 Answers

SOURCE: my catalytic converter is haveing

The dealer is paid a fixed price by the factory to perform warranty work. This price is normally less than the normal cost of doing the repair. Because he is already losing money on the repair he is not going to do any extra work to accomplish the repair especially if the extra work is not something that is factory made.
You are lucky he is even willing to make the repair because most dealer's refuse to warranty anything that has been modified from factory and the factory will back them up. They lay the blame on the modification. I'm afraid you'll have to do what he says if you want the work done. Hope this helps.

Posted on Aug 29, 2010

nebby58

Ben Norgaard

  • 257 Answers

SOURCE: Do I need to remove

I do not know about your specific vehical, but I do know that jeep owners run some of the best online forums in the world. I am sure it will give step by step directions on how to install the skid plate. I hope this helps! Please give me a 4 thumbs up review!

Posted on Apr 19, 2011

Testimonial: "thank you for the info"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai 2004 v6 need to replace starter-need to remove skid plate


This is more a dust cover. Look around the perimeter of it and remove the screws/bolts that you see. Start pulling down, if you missed one, it will be stuck there.

Sep 07, 2015 | Hyundai Cars & Trucks

1 Answer

I need step by step on replacing washer fluid tank


Remove belly "skid plate air dam" cover to inspect
Remove front bumper assembly to expose the guts Thread Washer fluid leaking and headlamp washers powering but no water

Mar 03, 2014 | 1998 Volvo V70

1 Answer

Where is the oil drain plug on a 2008 528i bmw? which skid pan do u remove to get to it ?


there is a access cover, you do not need to remove the skid plate.from under the vehicle you can easely tell the small plastic cover that needs to be removed

Feb 06, 2011 | 2008 BMW 528i Sedan

1 Answer

How to get the half shaft out


Halfshaft -sorry but the diagrams didn't paste into the fixya.com window, just the text. Also, this was for a 3.2L engine.
REMOVAL & INSTALLATION

  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Negative battery cable
    • Front wheel
    • Radiator skid plate
    • Transfer case skid plate
    • Brake calipers and mounting bracket
    • Brake rotor
    • Wheel speed sensor
    • Steering knuckle

  3. Support the axle housing with a jack. Unbolt the axle mounting bracket and
    remove the halfshaft/bracket assembly.
    To install:

  4. Install or connect the following:

    • Axle/bracket assembly. Tighten the bracket flange bolts to 85 ft. lbs. (116
      Nm) and the bracket mounting bolts to 112 ft. lbs. (152 Nm).
    • Steering knuckle
    • Wheel speed sensor
    • Brake rotor
    • Brake caliper and mounting bracket. Tighten the bracket bolts to 115 ft.
      lbs. (155 Nm).
    • Transfer case skid plate. Tighten the bolts to 27 ft. lbs. (37 Nm).
    • Radiator skid plate. Tighten the bolts to 58 ft. lbs. (78 Nm).
    • Front wheel
    • Negative battery cable

  5. Check the wheel alignment and adjust as necessary.





    Fig. 1: Exploded view of the left halfshaft, axle shaft and
    axle disconnect
    7924bg26.gif






    Fig. 2: Exploded view of the right halfshaft and mounting
    bracket
    9308bg03.gif



prev.gif next.gif

Oct 31, 2010 | 2002 Isuzu Rodeo Sport

3 Answers

My hyundai Santa fe is leaking transmission fluid somewhere at the front of the engine. I can't see it because of the skid plate. Any ideas of what it could be?


Good Evening. Unfortuantely there is no easy path to a right answer here without removing the skid plate. In front of the engine are transmission cooler lines and other miscellania. The best advice i could give you is take down the skid plate and have a can of brake cleaner handy to clean everything off while you have it turned off then have someone turn it on for you so you can visually see where it is coming from. Hope this helps and if you have any more questions feel free to ask.

Aug 14, 2010 | 2004 Hyundai Santa Fe

1 Answer

Replacing the skid plate on 07 Tahoe Z71


Remove bumper or use a swivel adapter to remove

Apr 29, 2009 | 2007 Chevrolet Tahoe

1 Answer

Nissan 2005 maxima plastic cover under the engine came down


this is called your skid plate, it is there in case you run over a curb or something of the sort, these things are rather flimsy and tend to brake easily, check to see if the holes where the skid plate's should be located are broken. If this is the case a cheap fix that gets the job done would be to purchase some zip ties and secure the skid plate with those. The other two alternatives would be to either purchase a new skid plate, or remove your skid plate and bank on not running over any curbs :) good luck!

Jan 29, 2009 | 2005 Nissan Maxima

1 Answer

Where is the starter on a 1995 Mazda MPV van?


it is located under the skid plate. you'll need to remove the front drive, the alternator, and power steering pump out to remove the starter. need to remove the bottom cover to see it.

Nov 18, 2008 | 1995 Mazda MPV

1 Answer

Replace the face skid in the front bumper


remove front bumper and it should be clear what holding the face skid in place

Sep 29, 2008 | 2008 Honda Pilot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...