Question about Cars & Trucks
Take it to a qualified repair shop an have a full vehicle scan done . Do you know what that is ? Hooking up a factory or professional scan tool an checking for code's in all the modules on the vehicle , instrument cluster , SJB - smart junction box - ford's BCM , What do you mean it remains on empty ? What have you done ? Did you replace the fuel level sending unit in the tank ? Replace instrument cluster ?
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1202 Fuel Sender Circuit Open Instrument Cluster Go To Pinpoint Test B . B1204 Fuel Sender Circuit Short to Ground Instrument Cluster Go To Pinpoint Test B .
Instrument Cluster Self-Test Mode
To enter the instrument cluster self-test mode with the engine off, press and hold the odometer reset button (base cluster) or simultaneously press and hold the message center reset and setup buttons (message center cluster). Turn the ignition switch to the RUN position and hold until the display indicates tESt (base cluster) or TEST (message center cluster) usually within 3 to 5 seconds. Press the reset button once to advance to each stage of the self-test.
To exit the instrument cluster self-test mode, turn the ignition to the OFF position. If no DTCs related to the concern are retrieved, GO to Symptom Chart .
Posted on Oct 17, 2018
You can look at a wiring schematic for the fuel system and find the power/ground wires for the fuel level sending unit. Jump those two wires and see if your fuel gauge shows full. If it does then you’ll need to replace your fuel sensing unit or the complete fuel pump module. The new fuel pump module will come with the sending unit on it. If it doesn’t change then there’s an issue in the harness or the instrument cluster.
Posted on Jul 15, 2019
Steps to Brother hl-l2340dw Wireless Setup:
Open the container for your new printer and remove every one of the stickers. Counting the one with some clever directions about delicately shaking the print cartridge side to side.
Attachment in the power rope, some place generally near your switch.
Hit the power switch on the correct side.
Hang tight for it to get done with booting totally (not any more flickering lights or sounds).
Utilize a pen to hold down the concealed catch on the back (pic underneath) for 3 or 4 seconds to initiate the "WPS" arrangement.
It should print a sheet of paper - get the PIN.
FOR MORE INFORMATION OR HELP VISIT ON GIVEN LINK:
Posted on Jul 15, 2019
if you have your stereo code you need to disconnect the negative side of the battery and while its dissconnected you need to turn the ignition to the start position a couple of times and then reconnect the battery this should discharge any residual electricity now when you turn your ignition on your dash instruments should reset
Posted on Aug 18, 2009
It could consist of skipping, engine cutting off or hesitates from starting, idling . Bad gas gives numerous signs, the best way I have found to deal with this is, Buy a octane booster 104, go to the gas station and put a couple of gallons of high premium in to tank to disperse the water in the gas. They also make a liquid to take water out of gas which also goes into the tank.
Posted on Jan 24, 2010
Have a 2006 expedition that died. Towed it back home and found that the #12 fuse was blown. Replaced the fuse and it started back up. After it started I gave it some gas and it died. It will not start again. I checked the fuse and it is not blown now. Any ideas????
Posted on Dec 09, 2010
Tips for a great answer:
Dec 15, 2015 | 2006 Ford Expedition
Apr 14, 2013 | 2006 Ford Expedition
Jun 26, 2012 | 1999 Ford Expedition
Mar 25, 2012 | 2006 Ford Expedition XLT
Aug 05, 2011 | 2000 Ford Expedition
Jan 04, 2011 | 1999 Ford Expedition
Dec 18, 2010 | 2006 Ford Expedition
Sep 11, 2010 | 2006 Ford Expedition
Apr 13, 2010 | 2006 Ford Expedition
Aug 04, 2020 | Cars & Trucks
287 people viewed this question
Usually answered in minutes!