Question about Hyundai Cars & Trucks

Open Question

How do I get a front wheel hub off a Hyundai iload 2011

Studs have been stripped

Posted by diane on

Ad

5 Related Answers

Anonymous

  • 132 Answers

SOURCE: Hyundai excel x3 front wheel

soak good with wd40 first then use a short piece of wood and a hammer to belt them off careful not to hit the axle with the hammer hope this helps glenn..........

Posted on Nov 25, 2008

Ad
CRTN

Michael Fisher

  • 716 Answers

SOURCE: Do I need to replace wheel studs or entire hub for front 1995 960

You Can Replace The Wheel Studs Call Napa And Find Out How Much They Are. Dont Go Dealer Cause They Are $20 A Piece And At Napa Like $4 Also You Can Try Autozone Or Kraigen But They Never Have The Ones I Need. Its Also Very Easy To Do Yourself If You Can Change The Brakes You Can Do This. You Can Have Them Pressed In At Any Tire Shop Usually $5.
Happy Fixing
Sincerely,
Michael Scott

Posted on Jan 12, 2009

Ad
blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: broken off wheel stud on a 1998 hyundai elantra

CLICK HERE FOR VIDEO

Thanks for using FixYa - a FixYa rating is appreciated!!

Posted on Feb 20, 2009

gerry bissi

  • 4388 Answers

SOURCE: cant remove wheel hub

here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal

  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

Posted on May 25, 2009

Anonymous

  • 22 Answers

SOURCE: 2003 hyundai elantra gls front wheel stud broke

grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Posted on Jun 10, 2009

Testimonial: "excellent advice"

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a parts manual please bolts and studs that hold the chain and chain cover are stripped.


go google and type in-- parts manual for ( make and model not supplied )
if the bolts and studs are stripped then you will probably need thread inserts to make new threads for the bolts and studs , which you get from any good spare parts shops or tool stores

Jan 09, 2016 | Cars & Trucks

3 Answers

A couple of my lug nuts are stripped out. Will new nuts fit tighter?


Yes they will but also check the threads on the lugs and replace if damaged.

May 03, 2015 | Cars & Trucks

1 Answer

Manifold bolts stripped out can't connect my exhaust wat should I do I have yamaha ttr90 needing someone to walk me through


remove the manifold and use vice grips to grad the affected studs . Apply plenty of grip on the stud and screw out . Replace with good studs using a stud installer or double lock 2 nuts on the stud to enable you to screw it in.

May 06, 2014 | Cars & Trucks

2 Answers

Wheel stud


splines? you meant treads?
remove wheel, then drum. no year stated , but some years
have drum bolts, ,
see 2 screw holes in the dump, insert 8mm bolt to hole
screw in both bolts an drum pushes free.
the drum is off, , remove stud , put in new stud.
or if the new stud dont fit, the drum is bad. new drum time.

Sep 28, 2013 | Suzuki Sidekick Cars & Trucks

1 Answer

The bolts were loosen on driver from tire now it's stripped wut to do


you will have to remove the wheel, brake caliper and rotor and remove the studs. Then you will need to install new studs for which you will need a stud installer tool or you can use a lug nut and washers to pull stud through the hub. the stripped out studs can be removed with a hammer. make sure you have the clearance in the back of hub before pounding on them.

Oct 23, 2012 | 1998 Oldsmobile Eighty Eight

1 Answer

How to fix front strip stud


No the hub will have to be pulled off and the stud pressed out.

Oct 13, 2012 | 2008 Honda Accord

1 Answer

Replace windshield wiper arm on driver side-screw is stripped. can i do this on my own with basic tools? single mom


Is the screw stripped or the stud the arm goes down on? Also why do you think the screw is stripped? Reason I ask is, I can't see the problem but just wondering if the inside of the arm is stripped and giving you the impression the screw is stripped. I assume that you bought another and installed it and stripped the stud? If you can give me some details like what happened to strip the screw/stud.

Sep 09, 2010 | 2001 Ford Windstar

1 Answer

How to replace a wheel stud


You will have to remove your wheel hub, by removing the center cap, then removing it's retaining nut (it may have a cotter pin, or a crimped nut that you have to bend up to remove it). You will need a vise to press out the stripped stud. Use a socket that's a little larger than the stripped stud so the vise will press it out as you tighten it. To press in your new stud, use the same socket on the opposite side so the new stud presses into place when you tighten it. It's really a easy repair, but you do have to have the tools to do it. As long as you have a decent set of hand tools, and a vise, you will be just fine.

I hope this helps you, and I wish you luck on your repair.

May 17, 2009 | 2003 Nissan Sentra

1 Answer

Broken/stripped rear lugs on pacifica that needs to be replaced


From Experience trying to clean the threads up usually results in just stripping the stud the rest of the way. Depending on how the car is set up (i.e. rear disc or rear drum brakes) replaceing the lug studs is fairly straight forward. All you need to do is remove the tire, remove either the brake drum or disc, and determine if you have room for removal and reinsertion of a new stud. If not determine what has to be removed to give you that room. Then comes the fun part. Take about a 2-3lb. hammer and knock the old one out. Yes, they just knock out. Then to instal the new one just set it in the hub where the old one came out, place a few washers that will fit over the knurled part at the base on the stud and the new lug nut and tighten it down til the back side if flat against the hub. Then just reinstall previously removed parts and you are done.

Apr 01, 2009 | 2004 Chrysler Pacifica

1 Answer

Lug stud


Here's another thought - if the stud isn't too badly stripped, you may be able to use a re-threading die to restore the threads. The thread type and size will depned on the make and model of your car. An autmotive parts store can usually help with this.
------------------------------

If you must replace the stud,

A bad stud can usually be driven out through the back of the axle flange. You said the stud was stripped. You can:

Force one of the lug nuts onto the stripped stud maybe two to three turns , then take a drift pin and drive the stud out the back. The stud will have grooves that hold it in place on the axle flange. You willl hhave to hold the stud head with vice grips and remove the lug nut to get the stud out.

To install a new stud, insert it from the back, add a little grease to the knurls (grooves) and pull it into place with a lug nut. The stud must be firmly seated in the axle flange.

Mar 28, 2009 | 1998 Pontiac Trans

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Brad Brown

Level 3 Expert

18564 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...