What is the torque specs.on inner and outer tie rods on a 2005 ford ranger?

Question edited for clarity, MAKER.
Question moved to model category.

Torque spec question : 2000-2005 (other than GXP)

http://www.pontiacbonnevilleclub.com > topic52656
Jul 4, 2020 · 4 posts · 3 authors
Stabilizer bar link nut 13 ft.lbs. Strut mount nut 55 ft.lbs. Strut mount to body 35 ft.lbs. Strut to knuckle 135 ft. lbs.
2000 Torque Specs : Specifications and General Information
1 post
May 21, 2008
Quick Torque Specs Question : 2000-2005 (other than ...
2 posts
Sept 27, 2014
stupidly over done topic but need some questions answered
6 posts
Jun 17, 2016
Broken spring : 2000-2005 (other than GXP)
6 posts
May 19, 2019
More results from www.pontiacbonnevilleclub.com

2004 bonneville se: steering..torque specs for tie rod..strut..bolts

https://www.justanswer.com > ... > Pontiac Problems
Jun 22, 2010 - lbs.) Strut Mount to Body Nut, 47 Nm (35 ft. lbs.) Strut to Knuckle Nut, 147 Nm (108 ft.
1 answer · Top answer: Tie Rod Inner to Gear 100 Nm (74 ft. lbs.)Tie Rod (Front) Lock Nut 64 Nm

• Axle Shaft nut - 177 ft-lb
• Hub and bearing assembly to steering knuckle bolts - 133 ft-lb

2003 chevy silverado 1500 4.3 v6. Changing steering rack and

https://www.justanswer.com > ... > Chevrolet Repair
Jan 11, 2021 - Below are the torque specs you requested: Steering Rack-to-frame mounting bolts: 136 lb. ft. Outer tie rod nut: 37 lb. ft. Outer tie rod ...
1 answer · 1 vote: Coupler clamp bolt to the intermediate shaft: 33 ft. lb.

• 
  

  Torque specs for tie rod end castle nuts - JustAnswer

  https://www.justanswer.com > chevy > 2p3g8-torque-sp...
  Oct 24, 2009 - Tighten the clamp nuts 18 ft. lbs. (25 Nm) (except C3HD). On C3HD models, tighten the clamp nuts to 65 ft. lbs. (88 Nm.

People also ask

44-59 lb. ft.

Should be just one ugga dugga

59 ftlbs

Hope this will answer your question,If do pls click on helful botton and you can follow me at fixya,so I can answer your question faster.thanks.

Here are the tie rod end nut torque specs:
• Lower Control Arms - (Front and Rear bolt) 129 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Upper Control Arms - (Front and Rear bolt) 140 ft-lbs x2 and (Knuckle Stud) 37 ft-lbs
• Inner Tie Rods - 81 ft-lbs
• Outer Tie Rods - (Knuckle Stud) Tie Rod nut 44 ft-lbs and jam nut 55 ft-lbs
• Stabilizer Links - 17 ft-lbs
• Rear Shocks - Lower and Upper 85 ft-lbs
• Front Shocks - Module Bolt x2 37 ft-lbs, Module nut x3 37 ft-lbs and Stud nut 37 ft-lbs

webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

If you have electric steering(no power steering pump)you have to change the entire steering gear assembly as no part is available.If you have the system with a pump a part is available.In order to change the inner tie rod you would loosen the 21mm lock nut on the tie rod.remove the 18mm nut on the outer tie rod and spin off after removing the outer tie rod from the steering knuckle.Remove the nut and the inner and outer clamps on the tie rod boot.remove the boot.You would then need a special inner tie rod tool to turn the threaded inner rod from the steering gear.

45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut