How to replace knock sensor 2011 chevy malibu 2.4l

Question edited for clarity.

Question moved to model category.

https://www.f150forum.com/f118/2015-3-5l-ecoboost-p0327-knock-sensor-help-527974/

Location of knock sensors on 2011 f150 3.5

Fixya https://www.fixya.com > Forum > Cars & Trucks
4 hours ago - Locate the knock sensor, which is located near the rear of the engine block, under the intake manifold. Disconnect the electrical connector from ...

2011 f150 3.5 need R&R instructions for knock sensors. Ty

JustAnswer https://www.justanswer.com > ford > etca9-2011-f150...
Aug 4, 2020 - In order to remove and replace the knock sensor on your 3.5 engine on your 2011 F 150 you are going to need to remove the intake manifold as ...
1 answer · Top answer: Thank you again, Juan, for choosing Just Answer for your questions. I hope I was able to answer ...
Where are the knock sensors located at on the 2012 3.5l
Jun 1, 2021
How do i replace a knock sensor on 2012 f150 3.5 l v6 eco boost
Jun 12, 2016
Have a 2016 F150 2.7l showing P0330 and P1013 error codes.
Aug 25, 2022
Where is the knock sensor located on a 2001 Ford F150 5 4?
Jun 5, 2011
More results from www.justanswer.com

Question edited for clarity.
Question moved to Chevy Malibu.

There is a good video on removing and replacing the check engine light bulb on a Mustang.

https://www.google.com/search?q=chevy+malibu%2C+change+the+%27Check+Engine+Light%27+light+bulb

Here are videos on removing the gauge cluster on a Malibu.

https://www.google.com/search?q=2011+chevy+malibu+remove+gauge+cluster

..

P0010, P0011 (Intake/Exhaust Camshaft Solenoid) 2013 Chevy Malibu
https://www.youtube.com/watch?v=-RhsWasBAXA
Replacing a Camshaft Position Sensor on a Chevrolet 2.4 Ecotec P0340
https://www.youtube.com/watch?v=uF9l2gtDYIk
GM 2.4 Ecotec Camshaft Position Sensor - How To Test & Replace
https://www.youtube.com/watch?v=dOvwSncdP0g
2011 Chevy Malibu 2.4 camshaft senors location
https://www.youtube.com/watch?v=YCNRrv4r2Uk
2013 Chevy Malibu P0014
https://www.youtube.com/watch?v=VLNnc8v8TVw

2009 LTZ/Cycling (on/off) Door Locks - Chevy Malibu Forum ...

www.chevymalibuforum.com/forums/showthread.php?t=6599

10 posts - ‎8 authors
02-17-2011, 07:26 AM ... Two or three times while driving( in motion) the door lockswill cycle two or three times through the lock/unlock positions and then will stop. ...Since i can't produce this glitch on demand there is no point taking it to the dealer. ...The Malibu system will not let you lock the doors when the door is open.

Door Lock Actuator Recall? - Page 4 - Chevy Malibu Forum ...

www.chevymalibuforum.com/forums/showthread.php?t=7950&page...

Sep 23, 2011 - 10 posts - ‎7 authors
When I was driving this afternoon, the car would unlock itself at random intervals. ... It is reasonable to expect that Chevy could design a car whose doors remain locked while the car is in motion. ... 2009 Malibu 2LT, Adopted 5-7-2011 ... If you can get them to replace ALL 4 of them for a $100 deductible, I'd ...

[PDF]2011 Chevrolet Malibu Owner Manual

https://www.chevrolet.com/.../Chevrolet/.../2011_chevrolet_malib... ChevroletChevrolet Malibu Owner Manual - 2011 ..... remotely lock and unlock the doors from up ... The trunk can only be opened when ...... the vehicle is in motion can be.

You need to take the back seat out. Remove the C-Pillar trim panels. Lift up on the package shelf. Unplug the wiring connector. I've had mine out when I changed the speakers.

BTW, Its Not a Bulb. Its a LED Assembly. Replaced as a whole unit. Unless your good with electronics and soldering.

hope it help

Unfortunately a 2011 Chevy Malibu key fob need professional programming. It requires special equipment to communicate with the car. The good news is I have some money saving tips for you.

1) Purchase the key fob online at: https://www.keylessentryremotefob.com/2011-Chevrolet-Malibu-Key-Fob-s/4413.htm

2) Find a local locksmith to program the key and remote, they will come to you for less than the dealer would charge.

The thing l find works a treat is airasol brake cleaner,give it a good spray should sort the problem..Good-luck....

Sounds like you didn't put the pushrods back in the proper locations. There are two different lengths in this engine and you may have one backwards

The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.