Question about Seat Cars & Trucks

1 Answer

2003 Chevy Taho brake line diagrams. I have a broken line that must be going to rear brakes. There was fluid flowing out on drivers side just about were front seat is under truck.

Posted by Wayne Moore on

Ad

1 Answer

john h

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Seat Master
  • 23,504 Answers

Yep follows frame and inside gas tank to rear wheel well to above axle 1999 2006 Yukon Tahoe Suburban front to rear axle brake line replacement... 2004 chevy tahoe brake line diagram Google Search the 3 diagram is the front to rear

Posted on Aug 07, 2018

Ad

5 Related Answers

motor1258

Mike Butler

  • 6674 Answers

SOURCE: 2000 chevy 1500 silverado- rear brakes overheating

Have someone push & release pedal while at wheel with problem. See if it takes a while or slow to release. If yes, have wrench ready on bleeder screw, and try again, if it sticks/holds, crack bleeder screw, if it releases, I'd replace hose.

Posted on Jan 18, 2009

Ad

Anonymous

  • 232 Answers

SOURCE: need Rear Brake Diagram for 1994 Chevy K2500 4x4

Here is the diagram,It is always a good idea to only disaasemble one side so you can use the other side as a reference,I also reccomend using a set od brake pliers,they will the disassembly and reassembly much easier.
0900c1528008f6a2.gif

Posted on May 30, 2009

Auto Master

Roy Funkhouser

  • 140 Answers

SOURCE: 00 Chevy Silverado... ABS EBCM diagram help??? Brake line hookups

Hello,
I hope this helps.






1ec2f93.jpg
Thank You,
Roy

Posted on Aug 28, 2009

Anonymous

  • 1 Answer

SOURCE: chevy avalance brake line diagram

Left front weel wobling mechanics says it needs new roters $600

Posted on Dec 17, 2009

Oscar Agnes

  • 347 Answers

SOURCE: Rear brake pad dragging

ADJUST THE BRAKE CLEARANCE ON ALL FOUR WHEELS.

Posted on Jan 01, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause there to be no brakes what so ever even after replacing all the broken brake lines and bleeding them all on a 2003 Hyundai elantra?


if this has anti-lock brakes it may be the HCU(hydraulic control unit) may have air in it. it may have to be activated to get all the air out.

Aug 27, 2015 | 2003 Hyundai Elantra

1 Answer

Need to bleed brakes on my 2002 Saturn SL 2. Would like diagrams or much more detailed instructions than Haynes manual is giving me.


START WITH DRIVER SIDE THEN PASSENGER SIDE REAR THEN PASSENGER SIDE FRONT THEN DRIVER REAR. USE A CLEAR HOSE OVER THE BLEEDER VALVUE SO YOU CAN SEE THE FLUID PUT OTHER END IN THE BOTTLE OF BRAKE FLUID
1. HAVE SOME ONE HOLD BRAKE TO FLOOR
2. OPEN THE BLEADER VALVE ENOUGH TO ALLOW FLUID TO FLOW
3. SEE IF YOU SEE AIR BUBBLES IN THE HOSE
IF NO AIR BUBBLES CLOSE BLEEDER VALVE
REPEAT FOR EACH WHEEL

Aug 08, 2011 | 1997 Saturn SL

1 Answer

Brake fluid leaking on right rear tire of my 2003 taho


this happens when your wheel cylinder goes out, pretty cheap fix but usually end up breaking the brake line that leads into the wheel cylinder

Feb 12, 2011 | 2003 Chevrolet Tahoe

2 Answers

How do i take off the brake drums on a 2003 chevy cavalier


After you remove the tire, the drim should slide off. If it doesn't then try using a rubber mallet and gently tap on the outside edge as you pull on it. Sometimes you also need to tap on the drum in the center part. I have sprayed penetrating lubes like WD-40 or PB Blaster into the seam at the center. You may also have to back off the parking brake cable or even use the adjuster to back off the shoes.

Jan 27, 2011 | 2003 Chevrolet Cavalier

1 Answer

Bleed the brake lines


start at the passenger rear tire, have someone PUMP up brakes and hold pressure on them, release pressure by locating small bleeder screw, loosen screw 1/4 turn, brake fluid/air should come out, after brake petal reaches floor tighten bleeder, repeat process until only brake fluid comes out. go to driver side rear repeat, go to pass. side front repeat, go to driver side front repeat, after each bleeding make sure you check brake fluid in reservoir.

Sep 24, 2009 | 1984 Ford Mustang

1 Answer

What is the proper way to bleed my rear brakes?


There are to ways to blled your rear brakes first way is a gravity bleed take the top off the master cylinder fill it with brake fluid then open both bleeder screws on the rear once you get a flow of brake fluid coming out you can close them fill up the master and dont forget to pump your brakes before you start the car or you can have someone sit in the car and do the pump down method. Have that person pump the brakes until the pedal is hard tell them to push down on it you open the bleeder screw and the pedal will go to the floor and fluid will come out of the bleeder screw advise that person to not let the pedal go until you close the line once you close the line do it again til you get a straight flow of fluid coming out then repeat the same thing on the other side, Always start on the rear passenger side then the rear drivers side and keep an eye on the master cylinder you dont want to run it dry and when pump bleeding it the top should be on the master. Good luck

Jul 30, 2009 | 1996 Mercury Cougar XR7

1 Answer

Power steering and brake line location2002 Chevy Silverado 2500HD


the power steering lines are very short hoses approximately 8 inches long that go from the power steering pump down to the steering box, which is located on the frame, just below the pump. The brake lines run from the master cylinder(where you fill it with fluid on the drivers side firewall) down to the frame, and then follow the frame both directions; both to the front end and the rear end, along the drivers side frame rail, just on the inside of it. The fuel line runs along the same path to the rear.

Mar 03, 2009 | 2002 Chevrolet Silverado 2500HD

1 Answer

Rear wheel lock up/driver side/2wheel drive


spider gears in rearend r broken and binding up on the ring gear

Dec 19, 2008 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Adam Truesdale

Level 3 Expert

634 Answers

old marine
old marine

Level 3 Expert

2315 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...