Question about Saturn Cars & Trucks

1 Answer

2003 L200. Where is canister purge valve? - Saturn Cars & Trucks

Posted by Alberto Vanegas on

Ad

1 Answer

Micah G

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The purge valve solenoid is upfront under the hood, to the left of the engine near the coolant tank.

Posted on May 04, 2021

Ad

5 Related Answers

Anonymous

  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: where is the canister purge valve located

it is located near the fuel tank under the truck.

Posted on Apr 13, 2009

scott

  • 532 Answers

SOURCE: I need to locate the canister purge valve and the

look above the spare tire under the back of the box

Posted on Oct 24, 2009

nighttrain_r

Josh Canaday

  • 444 Answers

SOURCE: where is the canister purge valve located on a 2003 nissan altima 2.5s

it should be on the emissions canister itself

Posted on Mar 13, 2012

cargod01

Richard Wick

  • 4 Answers

SOURCE: Purge valve solenoid canister located on a 2003 Ford Taurus code po457

  • Park the Taurus on a level surface, set the parking brake and turn off the engine. Chock the wheels.
  • Open the hood and disconnect the negative battery cable.
  • Stand on the passenger's side and shine the flashlight along the firewall.
  • Look for a plastic cylindrical object about 2 inches high, mounted on the firewall near the right fender. This is the purge valve. You should see a thick black hose entering it from the driver's side of the unit.
  • The Ford Taurus canister purge control valve is a part of the evaporative emission control system, which keeps fuel vapors from escaping into the atmosphere. Pressure inside the gas tank fluctuate due to fuel level, environmental conditions and driving style. The extra vapor is vented into a storage canister under the rear of the car, outside the fuel tank, and is fed into the purge control valve through a rubber hose. The power-train control module monitors fuel tank pressure through a tank pressure sensor. It opens the canister purge valve as necessary to keep this pressure within design limits.

Posted on Feb 18, 2017

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I would like to know about code Po443 on my 2003 ford escape 3.OL I purchusad a new EGR Valve and A new solinide did i order the wrong parts?


P0443 FORD - EVAP Purge Control Circuit Possible causes Faulty Evaporative Emission (EVAP) Purge Solenoid Control Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection What does this mean? When is the code detected? - An improper voltage signal is sent to ECM through the valve. Possible symptoms Engine Light ON (or Service Engine Soon Warning Light) P0443 Ford Description The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.
Hope this helps

Read more:

Nov 07, 2017 | Ford Cars & Trucks

2 Answers

I have a 2003 ford escape 3.L and a code came up as po443 my unerstanding it is my egr valve and the solinide is this correct or did i purchas the propper parts for this code


P0443 FORD - EVAP Purge Control Circuit Possible causes Faulty Evaporative Emission (EVAP) Purge Solenoid Control Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection What does this mean? When is the code detected? - An improper voltage signal is sent to ECM through the valve. Possible symptoms Engine Light ON (or Service Engine Soon Warning Light) P0443 Ford Description The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Nov 07, 2017 | Ford Cars & Trucks

1 Answer

Purge valve solenoid canister located on a 2003 Ford Taurus code po457


  • Park the Taurus on a level surface, set the parking brake and turn off the engine. Chock the wheels.
  • Open the hood and disconnect the negative battery cable.
  • Stand on the passenger's side and shine the flashlight along the firewall.
  • Look for a plastic cylindrical object about 2 inches high, mounted on the firewall near the right fender. This is the purge valve. You should see a thick black hose entering it from the driver's side of the unit.
  • The Ford Taurus canister purge control valve is a part of the evaporative emission control system, which keeps fuel vapors from escaping into the atmosphere. Pressure inside the gas tank fluctuate due to fuel level, environmental conditions and driving style. The extra vapor is vented into a storage canister under the rear of the car, outside the fuel tank, and is fed into the purge control valve through a rubber hose. The power-train control module monitors fuel tank pressure through a tank pressure sensor. It opens the canister purge valve as necessary to keep this pressure within design limits.

Feb 18, 2017 | Ford Taurus Cars & Trucks

1 Answer

Code P0443


Error Code: P 0443
Description:
Evaporative Emission (EVAP) Canister Purge Valve - Circuit Malfunction
Problem Area:
Wiring, or VSV connector loose or detached.
Evaporative emission (EVAP) canister purge valve.

Feb 24, 2014 | 2003 Mitsubishi Montero

1 Answer

Evap code p0441


Error Code: P0441
Fault Area:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Feb 06, 2014 | 2003 Toyota Land Cruiser

1 Answer

Code p0443


Fault Code:- P0443 Indicates a Power-train fault


The fault is generally due to a problem in the Emission Control area


Fault Description: EVAP canister purge valve circuit malfunction

Action of ECM:- ECM Default: - Canister purge inhibited - Adaptive fuel metering inhibited


After clearing the DTC, complete the Purge system monitor drivecycle
Check for a reoccurrence of fault DTC.


Possible Fault:- EVAP Canister purge valve to ECM drive circuit: open circuit, short circuit, high resistance EVAP Canister purge valve power supply circuit: open circuit, short circuit EVAP Canister purge valve operating vacuum hose leak / restriction EVAP Canister purge valve failure

Check fault codes here http://www.bluejag.co.uk/diagnosticcodes.php

Aug 22, 2013 | Jaguar X-Type Cars & Trucks

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    3 Answers

    Po446 evap vent code where is the evap vent located


    Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

    Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

    Here it is:
    1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
    2) Take the bracket loose with a 5/8 wrench.
    3) Spin the valve around so the side with the hole is facing you.
    4) Take an air compressor and blow the vent valve out.
    5) reinstall and clear the code and it's fixed.

    Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

    Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
    Models:
    - 1999-2003 Chevrolet Silverado Models
    - 1999-2003 GMC Sierra Models
    --------------------------------------------------------------------------------
    This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
    --------------------------------------------------------------------------------
    Condition
    Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

    Cause
    Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

    Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


    Removal & Installation
    Purge Solenoid Valve-2.2L (L61) Engine
    1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
    2. Disconnect the vacuum pipe from the EVAP canister purge valve.
    3. Disconnect the purge pipe from the EVAP canister purge valve.
    4. Remove the EVAP canister purge valve and bracket.
    5. Remove the EVAP canister purge valve from the purge bracket.
    6. Inspect for carbon release in the EVAP canister purge valve ports.
    To install:
    1. Install the EVAP canister purge valve on to the purge bracket.
    2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
    3. Connect the purge pipe to the EVAP canister purge valve.
    4. Connect the vacuum pipe to the EVAP canister purge valve.
    5. Connect the EVAP canister purge valve harness connector.
    6. Remove the air cleaner outlet resonator.
    7. Disconnect the EVAP canister purge valve harness connector.
    8. Disconnect the engine purge pipe from the EVAP canister purge valve.
    9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
    10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
    11. Remove the EVAP canister purge valve along with the mounting bracket.
    12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

    Purge Solenoid Valve-2.4L Engines
    1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
    2. Remove the rear purge pipe from the EVAP canister purge valve.
      NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
    3. Disconnect the EVAP canister purge valve electrical connector.
    4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
    5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
    6. Remove the bracket.
    To install:
    1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
    2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
    3. Connect the EVAP canister purge valve electrical connector.
    4. Connect the rear purge pipe to the EVAP canister purge valve.
    5. Connect the front purge pipe to the EVAP canister purge valve.

    Vent Solenoid Valve-2.2L & 2.4L Engines
    1. Raise the vehicle
    2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
    3. Remove the hose from the EVAP canister vent valve.
    4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
    5. Remove the clip from the EVAP canister vent valve harness connector
    6. Disconnect the EVAP canister vent valve harness connector.
    To install:
    1. Connect the EVAP canister vent valve harness connector
    2. Install the clip into the EVAP canister vent valve harness connector.
    3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
    4. Lubricate the hose end with lubricant.
    5. Install the hose to the EVAP canister vent valve.
    6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
    7. Lower the vehicle.

    Hope this help (remember commetn and rated this).

    Apr 21, 2010 | 2000 GMC Jimmy

    2 Answers

    Describe your 1996 Ford Explorer Problem..trouble


    Diagnostic Trouble Code (DTC) P0443 indicates a failure in the EVAP canister purge valve circuit.
    Possible causes:
    • VPWR circuit open.
    • EVAP canister purge valve circuit open.
    • EVAP canister purge valve circuit shorted to PWR GND.
    • EVAP canister purge valve circuit shorted to VPWR.
    • Damaged EVAP canister purge valve.
    • Damaged PCM.

    Jul 10, 2009 | 1996 Ford Explorer

    1 Answer

    Where is the canister purge valve located


    it is located near the fuel tank under the truck.

    Apr 13, 2009 | Honda Pilot Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    189 views

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14869 Answers

    Joe Taylor
    Joe Taylor

    Level 3 Expert

    2228 Answers

    john h

    Level 3 Expert

    23915 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...