Question about 2005 Ford Escape

Open Question

I need to locate the engine coolant sensor on a 2p05 ford escape 3.0

Posted by Billy Bohannon on

Ad

5 Related Answers

robdan3

  • 2 Answers

SOURCE: Ford 460 Engine Temp sensor

looking at  the  front of  the engine, just to  the right and behind  the  distributor cap. You  will  see a  wire attached (push on).

Posted on Aug 24, 2008

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: need location of coolant sensor on 2002 chrysler 300m

near the thermostat I think, look for this part.

f2e8303.jpg

Posted on Apr 22, 2009

Ad

jatncbeach

  • 225 Answers

SOURCE: Need locations of o2 sensors in a 04 Ford Escape.

bank 1 sensor 1 is next to the fire wall. on the upper end of the exhaust

Posted on Aug 14, 2009

Testimonial: "Thank you for your help!!"

Anonymous

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

bschilz

Bill Schilz

  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am having difficulty locating it. I need to know how to locate and replace a thermostat on a 2002 ford escape


Follow the top radiator hose down to where it connects to the engine. You should find a dome shape item or a couple of smaller bolts that attach to the engine to the side of the radiator hose and the thermostat will be inside the housing. You will need to drain the radiator, remove the bolts holding the thermostat housing to the engine and remove the old stat and put in a new one be sure to make note of how the stat is facing when you remove it and put the new one in the same way. then reconnect the thermostat housing making sure the gasket is in place so it won't leak, then refill the radiator slowly so you don't cause an air lock in the radiator, with cap still off start the engine and allow it to warm up until the stat opens and then you will need to add more antifreeze to the system. Double check for any leaks. Turn on the heater and make sure you have good heat and you should be good

Jan 11, 2016 | Ford Cars & Trucks

1 Answer

Cooling problem,code#P1299,on a 06 Ford Escape 2.3l


P1299 - Cylinder Head Over Temperature Protection Active Description: Indicates an engine overheat condition was detected by the cylinder head temperature (CHT) sensor. An FMEM strategy called fail-safe cooling was activated to cool the engine. Possible Causes:
  • Engine cooling system concerns
  • Low engine coolant level
  • Base engine concerns
Diagnostic Aids: Refer to Section 1, Powertrain Control Software , for more information on the fail-safe cooling strategy and cylinder head temperature sensor. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test DL .


Feb 19, 2015 | 2006 Ford Escape

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

Where is the crank sensor located on a 2003 ford escape


2.0Liter engine is
Crankshaft Position Sensor Notes View 151-6 102969750
On a 3.0 Liter engine

Crankshaft Position Sensor Notes View 151-3 102969749
Hope this helps

Dec 11, 2009 | 2003 Ford Escape

Not finding what you are looking for?
2005 Ford Escape Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...