Question about 1992 Mitsubishi Pajero
The best solution you'll get from books at www.reliable-store.com
These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicle- cars, atv, trucks. forklifts, boats, excavators etc.
Posted on Jun 14, 2018
There could be a fusible link under the hood off the starter relay that is burnt out.
Posted on Oct 13, 2008
I think I have found the problem. When I wiggle the ignition switch the turn signals and radio go on and off so I feel the issue is in the ignition switch. From what I understand the actual electronics for the switch are at the base of the sterring column behind the lower dash panel and is connected by a rod that may need adjusting.
Posted on Jan 04, 2009
SOURCE: power windows wont work
All things Capri are at //www.techcapri.com/
The manuals are there - check them out ...
Wiring diagrams are there. Probably fixed by now anyway.
Posted on Jan 07, 2009
long answer but should get you solved.
You know for some reason jeep eliminated the FC relay for some models and now relies on the computer to determine when and at what speed the fan should run based on coolant temperature inputs and A/C compressor status. If the fan is not working properly i would consider replacing the fan,
"I have a 04 GC also with the 4.0 and I could not find my FC relay either. Nobody at a local dealer here had ever heard of this phantom FC relay problem. I was able to find an electrical diagram on the web that does not show the FC relay for the 04 GC but that was it. The diagram only showed the PCM and two relays in the PDC near the battery. My GC was overheating now and then. It would seem to overheat when you were in stop and go traffic or letting it idle. I was not losing any coolant so I replaced the thermostat but that did not fix it. After much frustration I started the engine and sat there and watched it run until it began overheating. I paid particular attention to the fan. When the engine began to overheat the fan was barely spinning and would even shut off at times during the overheating. I knew this was not right so that is when I began this search for the FC relay but I could not find it. I disconnected the fan and did some checking on the two speed electric radiator fan. It has a 3 pin connector where the center pin is ground. When I ran power to one pin and grounded the center pin the fan would run. However when I switched the power to the other pin I got nothing. I had already checked operation of the Low and High Speed relays in the PDC near the battery and all checked out so I went and picked up a new radiator fan assembly and installed it. That was yesterday and that fixed the overheating problem. I have concluded that for some reason jeep eliminated the FC relay for some models and now relies on the computer to determine when and at what speed the fan should run based on coolant temperature inputs and A/C compressor status. I also found out that although my GC does not have the towing package it does have the max cooling package. When I went looking for a new motor for the radiator fan at local auto parts store I was asked if it had the towing package and I answered no. Everytime I did they would bring out a motor that only had a 2 pin connector. Not one of them kept the motor that would be needed if you had the towing package. I bet if they did it would have a 3 pin connector on it. So while my GC does not have the towing package I think it has the max cooling package that usually comes with the towing package. I think the standard cooling package uses a one speed fan where the max cooling package uses a two speed fan. It may be that the standard cooling package uses the FC relay which is supposed to be under the passenger headlight but the max cooling package eliminates the relay and uses the PCM to control two relays in the PDC which in turn run the fan. One more thing....replacing the radiator fan assembly involves removing the shroud. One of the 4 screws that holds the shroud is in a very tight space. I fianlly got to it with a long socket extension and swivel. I know this is long but I hope it helps because I was very frustrated at the lack of informartion available locally and on the web in reference to this oddity" (article found on web)
Posted on Jul 22, 2010
Tips for a great answer:
Dec 06, 2014 | 1992 Mitsubishi Pajero
Jan 06, 2013 | 2001 Chevrolet Suburban
Feb 25, 2011 | 2001 Ford Taurus
Feb 03, 2011 | 1992 Honda Accord
Dec 14, 2010 | 1990 Honda Accord
Jun 20, 2009 | 1993 GMC Sierra K1500
Jun 07, 2009 | 1992 Honda Accord
Nov 04, 2008 | 1992 Isuzu Trooper
Jun 25, 2008 | 1992 Honda Accord
41 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: