Question about 2008 Chrysler Sebring

Open Question

Where is the low pressure a/c switch located on a 2008 chrysler sebring

Posted by Janet Paroline on


5 Related Answers


  • 202 Answers

SOURCE: 2002 Chrysler Sebring Oil pressure light

Could be a bad oil pressure switch, or a bad oil pump. Both will cause this issue. Hope it is the switch b/c the oil pump is a costly repair.

Posted on Mar 26, 2009


Ned C Cook

  • 3433 Answers

SOURCE: Where is the starter located on a 1998 chrysler sebring coupe

Follow the +cable from the battery. The starter is on the other end.

Posted on Oct 21, 2009



  • 412 Answers

SOURCE: Where is the fuel filter located on a 2004 Chrysler Sebring Sedan

Some of the Sebrings have two filters(one is called a sock).The sock(which all sebrings have) is located in the fuel tank itself on the pump module.If this model is the JXI then the external filter is located on the belly of the car between the tank and drivers rear seat. I hope I could help!!!

Posted on Apr 29, 2010


  • 55 Answers

SOURCE: location of oil switch 2002 chrysler 2.7 engine

should be on driver's side right above the oil filter

Posted on Jul 18, 2010

SOURCE: 2008 AC Low pressure switch "Where is it"

it is on the accumulator the large metal tank that is next to the fire wall

Posted on Mar 27, 2012

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the oil sending unit on a 2008 chrysler sebring v6

Looks to be located just below the heat shield for the exhaust header on the right side. Here is images with locations:

Aug 16, 2016 | Chrysler Cars & Trucks

1 Answer

What is the location of the AC Schrader Valve on 2008 Chrysler Sebring LX 2.4L?

There are two valves of different sizes 1 high pressure and 1 low pressure. You should see two silver tunes coming from the radiator are usually on the passenger side of the car follow those ac lines and each one will have a valve on it. There should be a cap on each one. Most cars have them near the front of the car but on occasion they have been on the back by the firewall.

Jul 07, 2016 | 2008 Chrysler Sebring 2.4

1 Answer

2008 Sebring brake lights are not working.What can it be?

The brake light switch is located on the brake pedal arm under the dashboard. It may be stuck. Remove it and use electric/electronics contact cleaner spray to restore it's action. If the spring is broken inside it, replace the switch.

May 30, 2015 | 2008 Chrysler Sebring

1 Answer

Ac is not working in my 2008 Chrysler Sebring. We checked all the fuses, and tried to recharge the AC, but indicator said that the freon is full and there are no leaks. at this moment it is just bowin

Check the A/C compressor relay . Also ck the low pressure switch for the A/C system . you can unplug the low pressure switch and jump it with a paper clip to rule that out . Ck the A/C compressor fuse if you haven'y already

Aug 05, 2012 | 2008 Chrysler Sebring

1 Answer

Instrument panel lights suddenly stopped working the remaining cluster lights (low fuel, check engine, etc) work fine. I checked the dimmer switch and it works fine

I also had the instrument panel go out yesterday on our 2008 Sebring LX. I wish someone could give clear answers to the problem without bringing it down to the dealership. $$$

Feb 20, 2010 | 2008 Chrysler Sebring Convertible

1 Answer

Why does 2001 Chrysler sebring A/C cuts in and

It's low on refrigerant ( probably uses R-134a) available at WalMart. Low refrigerant pressure switch deactivates A/C compressor for safety reasons.

Sep 08, 2009 | 2001 Chrysler Sebring

1 Answer

My 2008 chrysler sebring will start the engine but

shift lock switch. this switch is usually connected to a little box on the brake pedal. Look about half way up the pedal from the foot pad and make sure the wires are still intact.

Aug 13, 2009 | 2008 Chrysler Sebring Convertible

1 Answer

1996 Sebring convertible locating low pressure port on the a/c? Where is it?

The smaller of the two lines is the high pressure line. The larger line is the low pressure line. The cap on the fitting should be blue in color on the low pressure side. Hope this helped and best wishes.

Aug 06, 2009 | 1996 Chrysler Sebring

1 Answer

2003 sebring a/c problem

check voltage directly at compressor if no power needs compressor. how did you check low pressure switch?

Oct 16, 2008 | 2001 Chrysler Sebring

Not finding what you are looking for?
2008 Chrysler Sebring Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides