Question about Cars & Trucks

1 Answer

2000 s10 turn signal flasher location

Turn signals dont work but hazard signals do

Posted by ron hillis on

Ad

1 Answer

Stan Ford

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 2,953 Answers

The location shifts from model to model, Turn on the hazard signal, the units are often side by side.

Posted on Jun 04, 2018

Testimonial: "thanks"

Ad

5 Related Answers

Anonymous

  • 20 Answers

SOURCE: location of flasher for turn signal

  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Posted on Nov 23, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: 1994 devilles flasher location

Turn signal flasher module is behind dash left of steering column near chime module. I have a 94 Seville and I had that same problem you need a Turn Signal Flasher Moduel, I forgot the proper term for it but I had to get mine replaced too. When I hit the signals to turn the side light would come on but the signal light wouldn't. Its a little box you get from Cadillac it only cost like $20 - $25 and you get it installed and trust. It'll work again. I just got mine done this week and my car now has turn signals again.

Posted on Dec 15, 2008

chuck943

Chuck Martin

  • 783 Answers

SOURCE: 1999 ford expedition turn signals not working

It is behind center of instrument cluster just above the accel pedal in the blower/flasher relay block,it is actually a relay on this vehicle.

Posted on Feb 28, 2009

Bob B

  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

Anonymous

  • 1 Answer

SOURCE: turn signals and hazard don't work

On my 2005 Dodge Caravan the turn signals and wipers suddenly stopped working.

Posted on Jan 26, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Dodge Intrepid "ES" model...turn signal/flasher doesn't work.


the flasher is under the dash on the drivers side. if you turn on the hazard lights and look under the dash you will see what turn signal flasher looks like and know which flasher not to change thinking its the right one. look for the signal flasher and change it.

Aug 24, 2014 | Cars & Trucks

2 Answers

I have a Frontier XE 2001. Niether turn signal works have good bulbs and fuses are OK. Where else should I look.


did both signal lights stop working at the same time or not,it may just be the signal flasher has gone bad,it is located under the dash by the fuse panel.if the hazard flashers work then i would say the signal flasher is bad.with the hazards on you can locate it and that is what the signal flasher looks like and it is a separate flasher,

Mar 31, 2011 | 2000 Nissan Frontier

1 Answer

Where is my turn signal switch or the flasher on


The turn signal switch is in the column, at the end of the turn signal lever. The flasher is integrated with the Hazard switch. The hazard/turn signal flasher is common to go bad.

Oct 28, 2009 | 2000 Pontiac Grand Am GT

1 Answer

The turn signals dont work on a 2000 Ford EXplorer


most likely not in the fuse box nor is it a relay, check the fuse and replace if necessary. Turn on your hazards and listen for a clicking sound under the dash on the drivers side. Normally the hazard and turn signal flashers or near each other. Not a Ford fan so I can't exactly say where it is located.

Aug 15, 2009 | 2000 Ford Explorer

1 Answer

Turn signals dont work at all


Try your hazard lights. If they work, then it's your turn signal flasher. With your hazards on, listen under the dash for the constant "clicking". Locate the flasher for your hazrads... the turn signal flasher should be near it. Once you find it, just pull it out and replace.

You can use your hazard flasher in place of your turn signal flasher, just swap the two. This will get you to the store to buy a replacement.

Jun 08, 2009 | 2005 Hyundai Accent

1 Answer

Renault laguna 1.9tdi dynamique 51 reg. hazard warning lights do not work, changed fuse still not working. whats wrong with them


If your turn signals work, then replace the flasher for your hazards. Turn your key on then give a left turn signal. Listen for the "clicking" sound near your brake pedal and accelerator. Once you locate your turn signal flasher (small, "cylinderical", device) the hazard flasher should be near it. Simply pull out the flasher and replace... just plugs in.

Jun 07, 2009 | 2000 Renault 181

1 Answer

Locating the turn signal flasher on 1993 corsica


The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Dec 03, 2008 | 1993 Chevrolet Corsica

1 Answer

1994 devilles flasher location


Turn signal flasher module is behind dash left of steering column near chime module. I have a 94 Seville and I had that same problem you need a Turn Signal Flasher Moduel, I forgot the proper term for it but I had to get mine replaced too. When I hit the signals to turn the side light would come on but the signal light wouldn't. Its a little box you get from Cadillac it only cost like $20 - $25 and you get it installed and trust. It'll work again. I just got mine done this week and my car now has turn signals again.

Nov 28, 2008 | 1994 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23577 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6576 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...