Question about Ford Cars & Trucks

1 Answer

What causes a clicking noise from front left drive shaft of my Ford Fiesta 1.4 2008 model.

Had it up of the wheel and not the cv joint. Nois is coming from inside the housing

Posted by Alastair Walters on

Ad

1 Answer

ray gallant

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 68,329 Answers

Bearing going out probably

Posted on May 19, 2018

Ad

5 Related Answers

Anonymous

  • 239 Answers

SOURCE: Steering Binding

Hello Goldwinger.
Yes it could be an axle, It could also be the strut tower The strut bearing is on top of your strut and could be a problem I have seen it before and also the Axle do that, I don't think it would be the steering rack because I think it would do that either way you turn the steering wheel. I would stick with your first thought. Axle, sure sounds like an axle, The Clicking is usually the First indication of that. So I would take it out and check it or just replace it and I think that will solve your problem. If not get back to me and when I get in from the Shop I will check back here and see if you got it or not. Thanks Goldwinger and hope that helps you out some what. Bear001

Posted on Jun 24, 2008

Ad
STEVIE_N_24

steve golladay

  • 147 Answers

SOURCE: popping noise during turn

Bad CV Half shaft on right hand side.Replace axle shaft assembly to cure problem.

Posted on Mar 29, 2009

SOURCE: need to replace front left cv axel

Best approach is to acquire a repair manual for that vehicle. Pep Boys or similar will likely have one..

Posted on Apr 28, 2009

Jonah Oneal

  • 14092 Answers

SOURCE: severe bearing noise from front wheel bearing/cv

you have to replace bearing and hub as a unit.you have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

Posted on May 03, 2009

Anonymous

  • 2 Answers

SOURCE: whining/grinding noise at deceleration

We have the same problem at our shop. We haven't rebuilt the front differential yet. We tried 3 different shafts on 2 different Jeeps and the noise is on both just the same. By greasing the front driveshaft cv joint, we got he noise to quiet some, but it is still way to loud. With the driveshaft out, the noise is gone. We are about to buy a new shaft from the dealer for $600. There are some service bulletins about some noisy driveshafts.

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

How to change cv joints on a Mazda b2500


Remove the wheel .remove axle nut. remove wheel hub. place drain pan under housing to catch oil. axle will pull out of housing .remove rubber boots remove wire clip and joint will come apart. you can obtain reconditioned shafts for a little more than the price of the two joints saves a lot of work

Jul 04, 2014 | Cars & Trucks

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

Cv joints


Hi Thomas, I have not changed CV's on your type of vehicle, but can give you the path to follow. Here we go; Always work with someone to assist you. pepare four plastic bags for use later. With both front wheels on the ground remove any wheel covers fitted. In the center of the wheel you will see the shafts of the CV's. These are held in position with large nuts, either locked with a tab or sometimes with a locking washer and split pin. Unlock whichever system is used and loosen the nuts on the shafts. Loosen the wheel nuts, jack up the vehicle and place chassis stands to support the vehicle and the lower it onto the stands. Remove the wheels and remove the center nuts from the CV joints. If the vehicle is fitted with McPherson struts, loosen the two through bolts and nuts, or if fitted with wishbone suspension loosen and remove the bolts securing the the upper ball joints. Swing the stub axle outward and downwards so that there is enough room to remove the CV shafts from from the hubs. Put on a pair of goggles and then climb under the vehicle and release the boots or retaining bolts holding the shaft into the spyder or inner CV joint. Once removed pull the half shaft out of the housings keeping everything as clean as possible and wrap in a plastic bag.. (There will be high impact grease inside both the inner and outer joints, This may have been thrown out in the event that the rubber boots are broken) If you are replacing the entire half shafts, carefully observe the way in which the inner joint is fitted. If there are no bolts, studs or nuts holding a flange onto the gear box differential housing, the inner joints will be held in place by spring loaded clips fitted around the ends of the inner shafts. If your vehicle uses that type of fitting the shafts will be levered out. It will be important to use a catchment tray to collect any transmission oil which leaks out. Cover the joint with one of the plastic bags. If you are fitting only the outer CV's, the defective units are knocked off the shafts with a heavy copper mallet (The shafts also have locking cur clips holding the shafts in place. Sometimes the inner basket of the CV bearing housing will need to be cut or broken out, so the the joint can be removed. Please both you and your friend use safety goggles during this procedure. Once removed, fit the new joint. If you are replacing the entire assembly and if they are the type using clips, use a thick piece of wood and hold the shaft as straight as possible then ask your pal to knock the shaft into the housing. The rest of the job is the opposite to removal. When fitting the outer CV shaft nut follow the correct tightening torque setting, as these usually hold the front wheel bearings at the correct settings and tightness. Regards John

Feb 14, 2012 | 2006 Chrysler Pacifica

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

Dear sir yes i ment cv joint & no it does


CLUNK NOISE YOU HEAR IS WORN CV JOINTS.

May 26, 2010 | 2003 Saturn VUE

1 Answer

How do you change the front left axel on a 1993 buick regal custom. It is making a clicking nois going in revers and forward a t low speeds


This is called a cv shaft. First jack the car up and support the vehicle with jack stands. This is for safety. Then remove the wheel and the brake caliper. you need to unbolt the tie rod end and separate it from its housing. You also need to unbolt the strut from the hub assembly. You might alos have to remove the bolt from the ball joint and remove it from the hub. In the center of the hub assembly is a large nut that will also have to be remove. This is actually holding the cv shaft to the bearing inside the hub. once you have removed the cv shaft from the hub, give it a straight hard **** away fromthe trans. There is a little c clip on the other end of the cv shaft which keeps it inside the trans. If the cv shaft separates into two pieces, this is ok. Take a small pry bar or flat head screw driver and place it between the part of the cv shaft left in the trans and the case. Be gentle but lightly pry against the cv shaft and it should come out of the trans. Reverse the order of disassembly and bang your done.

Sep 08, 2009 | 1993 Buick Regal

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

I dont know what it is called but the front right side wheel is making noise and i think it is the cv joint but not sure


Try checking the hub's and bearing's, when bearing's go bad they tend to make a squealing nois.

Apr 18, 2009 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...