Question about Volvo Cars & Trucks
THE REAR BUMPER SEEMS TO BE DROPPING OR HANGING ITS LOOSE
If you pull the trim off (use a plastic spatula to get under it, then just yank with your hands) there are holes in there to reach the bolts.
Get an extension and a socket, I think it's 12mm, and then see if you can just tighten them up a little bit.
Also, the bumpers hang on the body with some clips/grooves along the edges, so make sure that they didn't 'fall out' of the grooves and clips and sag that way.
If so, loosed the bolts, pull the bumper away from the car an inch or two and then push it back in place while aligning the bumpers edges.
Posted on Mar 10, 2019
Your CCM (Climate Control Module) is dead, or asleep. Look in the fuse box at the left end of the dashboard and pull the fuse and see if it resets the CCM. The module may need to be reprogrammed or replaced.
My suggestion is that you take this to a Volvo mechanic, one who has experience with working on these 1999- Volvo models. They have a networked computer system that requires special tools to diagnose and download software into the modules.
Also, it is a good idea to have them perform a total software upgrade, it will address many issues, and may prevent other issues from occurring.
Posted on Feb 13, 2009
The gas filter is located passenger side just forward of the rear axle. The band that holds the gas filter in place is a pinch band that has a nut welded/formed into it on the back/top side. A 12 mm bolt holds the band in place. The top of the band has a bracket that hold the return fuel line - this just pops off and the return fuel line can be reattached once the filter has been replaced. If your filter has never been replaced there is masking tape covering the pinch connections at both ends of the filter. Remove the masking tape. You need to put a pan under the old filter to catch any gas spillage - it will be minimal. Also the new filter comes with plastic caps on the ends of the new filter - you will want to use them to plug the old filter connectors so you need to take them off the new filter to have handy. Ther is a T off the inlet gas line that has a cap on it - remove the cap and press the needle in the T to relieve any pressure that is on the gas line - If it has been setting for an hour there will probably be very little if any pressure on the line. You can skip messing with the T and you will see about an ounce of fuel that will come out of the filter when you remove the hose.
To remove the connectors push the connector ring away from the filter housing. (I did the front first because I had more room). I used a paint can opener to help pry the hose away from the filter - it is shaped like a can opener but without a cutting edge - a large flat screwdriver would perform as well. It is a tight fit but once it starts to move it will come off. Once the hose is off use the plastic caps you took off the new filter to help hold the gas in the old filter. After removing both ends remove the holding band and place it on the new filter. The two lines will go back on easier than they came off, just push them onto the filters nipples. Put the 12 mm OR 10MM bolt back into the pinch band and reintall the return fuel line.
Posted on Aug 18, 2009
Tips for a great answer:
Dec 01, 2016 | 2004 Volvo S80
Dec 03, 2015 | 2000 Volvo S80
Jul 14, 2014 | 2007 Volvo S80 V8 Sedan
May 07, 2014 | 2000 Volvo S80
Jan 25, 2012 | Volvo S80 Cars & Trucks
Aug 28, 2010 | 2000 Volvo S80
Jun 20, 2010 | 2006 Volvo S80
Jun 02, 2009 | 2000 Volvo S80
Apr 09, 2009 | 1999 Volvo S80
61 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: