Question about Mazda Cars & Trucks

Open Question

I have a Mazda demio 2002 model and am changing the front wheel bearings ... does anyone know what the torque is on the hub nut

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009


mgray87

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

Ad

Ray Keckeisen

  • 599 Answers

SOURCE: 2005 Chevrolet Silverado 1500HD 4 wheel drive

177 ft lbs

Posted on Dec 09, 2009

Anonymous

  • 377 Answers

SOURCE: Does anyone know the torque wrench settings for

Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Posted on Jan 23, 2010

Randy Handy

  • 496 Answers

SOURCE: what is the torque specs for a hub and bearing assembly on a 2001 four wheel drive chevy s10 blazer


Adjustment

The wheel bearings on these vehicles are not adjustable. If the bearings become loose or make noise, they must be replaced.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. On 4WD vehicles, remove wheel center cap, if equipped, and the drive axle nut and washer
  3. Raise and support the vehicle.
  4. Remove or disconnect the following:
    NOTE Lay the hub and bearing on the wheel studs on the outboard side. This will avoid damaging the bearing seal.


    Tire and wheel Caliper, leaving the fluid lines connected Brake rotor Halfshaft from the hub and bearing on 4WD vehicles. Place a brass drift against the outer edge of the halfshaft to protect the shaft threads. Use a hammer to sharply strike the brass drift, but to do not remove the halfshaft at this time. Wheel speed sensor Wheel hub and bearing-to-steering knuckle bolts and hub and bearing


    Splash shield from the steering knuckle Seal from the hub and bearing

To install:
  1. Install or connect the following:

    Wheel hub and bearing seal Splash shield to the steering knuckle, making sure it-s properly aligned Hub and bearing to the steering knuckle, aligning the threaded holes Hub and bearing bolts and tighten to 77 ft. lbs. (105 Nm) Wheel speed sensor. Tighten the bolt to 13 ft. lbs. (18 Nm). Rotor and brake caliper Tire and wheel
    The Hub Bearing Torque - Front

    If Torque Specs are not in the box we recommend youtorque to this setting. Axle Nut: 103 Ft/Lbs.Flange Bolts: 77 Ft/Lbs. WARNING: Failure to observe the following warningscould create a risk of death or serious injury.Proper maintenance and handling practices arecritical.Always follow installation instructions and maintainproper lubrication.Every reasonable effort has been made to ensure theaccuracy of the information contained in thiswriting, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute forthe specific recommendations of your vehiclemanufacturer.Always use the recommended torque requirement unlessotherwise specified in the carton.Depending on the application, type of hub unitbearing and location, the installation process mayvary.Please review the vehicle manufacturer'srecommendation before removing or installingcomponents.
  2. Lower the vehicle
  3. On 4WD vehicles, install the drive axle nut and tighten to 103 ft. lbs. (140 Nm), then install the center cap.

Posted on Nov 10, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

What is the size socket required for a 2012 Ford Fusion Axle nut? Also, what is the Torque spec to secure it back on? Working with Front-Right wheel.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow
2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...
Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..
0helpful
1answer

How do I rgerplabe how do I replace a front wheel bearing?

TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.
1helpful
1answer

How do i pull the hub off my 2002 mazda , on drivers side front

REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel
3helpful
1answer

I want to know the torque spec for a wheel bearing on an Hyundai accent 2002

front hub axle nut 162-192 ft lbs.

lug nut 66-81 ft lbs.

rear hub nut 148-192 ft lbs.
0helpful
1answer

How much do i torque wheel bearings 2004 mazda mpv

wheel hub mounting bolt 75-90 ft lbs.

wheel hub lock nut 173-234 ft lbs. ( 2002 ) 173-202 ft lbs. ( 2003-04 )

lug nuts 79-108 ft lbs.
1helpful
2answers

Replacing the rear hub on a 2002 kia sedona when i went to take the hub nut off i didnt even need a socket it came off with my fingers is that normal. My manual says 177 to 199 ft lbs my torque wrench only...

You are talking about a hub on a spindle of a front wheel drive car? You took off the nut to get to the bearings? Pulled the pin and the nut just spun loose? Am I right so far?? If so, then yes, this is normal, no bearing gets tightened any tighter than finger tight or it will burn up. I don't know where the torque specs came form, unless they are talking about the caliper to hub bolts if there are any,it might be metric, 199 kilograms per centimeter or whatever they go by. But still wouldn't be for the bearings. Put the torque wrench away, I have never used one in my life, except for head bolts. Hope this helps.
3helpful
1answer

Does anyone know the torque wrench settings for the rear hub/wheel bearing nuts on a 2002 Peugeot 206 1100cc please? Also the road wheel bolts?

Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event
10helpful
3answers

Replace front wheel bearing is it hard to do on 2002 alero

its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).
20helpful
2answers
5helpful
1answer

MX5 Front Wheel Bearing

Easy fix. Remove the wheel, remove caliper and caliper bracket. Remove brake disc. Pry off hub dust cap. This can be difficult and sometimes the cap cannot be reused. They are inexpensive, however. The hubs are not rebuildable and must be replaced. Undo the large hub nut, remove old unit, replace, reinstall nut, crimp the detent at slot in spindle. (use a punch) Nut torque is #125 ft. pounds to 160. Reinstall cap, caliper bracket, etc.
Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

314 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15008 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...