Question about 2006 Ford Fusion

Open Question

Where is input speed sensor located? - 2006 Ford Fusion

Posted by teresa wilson on

Ad

5 Related Answers

fordexpert

  • 5692 Answers

SOURCE: 2006 Ford Fusion SEL - TPS

The TPS is an easy part to replace. It has 2 screws and 1 electric connector. It is about the size of a butane lighter and attaches to the metal airhorn.

There is only a slight adjustment possible for this part. One end has an elongnated slot for the screw. Just look at where the old part was adjusted and replace it that way. The only thing you need to watch is aligning the slot on the throttle shaft with the indentation on the TPS.

While you are replacing the part, disconnect the battery on the POS cable and this will reset the "check engine" light on the dash. Then reconnect and drive your car.

Posted on Apr 30, 2010

Ad

Anonymous

  • 5 Answers

SOURCE: 2006 Ford Fusion. Left front door inside handle

This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.

Posted on May 08, 2010

Ad
franktilt

Frank Rossiter

  • 403 Answers

SOURCE: 2006 Repair Manual Ford Fusion 1.4

autozone.com sign up its free then click on repair manuals you will find all of your info there....good luck

Posted on Jun 03, 2010

moparownr

Jeff Hammack

  • 667 Answers

SOURCE: my 2006 ford fusion check engine light is on and

P0882 - TCM Power Input Signal Low, this is a transmission code, I recommend that you take it to a dealer or qualified transmission shop. Hope this helps.

Posted on Jul 07, 2010

Anonymous

SOURCE: p2104 + p2112 car starts

P2104--Throttle Actuator Control System-forced idle

P2112--Throttle Actuator Control System-stuck closed

That could be anything from-----simply spraying the throttle
plate with CRC Throttle Body Cleaner,to Coil misfires ,coming
back on your TPS Sensor and setting your codes,to a bad
APP Sensor (accelerator pedal position sensor) to worse
case,a bad TACM (throttle actuator control motor)

The TACM you never want,because it requires a complete
new throttle body from Ford --for the tune of over $600 just for the
part. That forces you to install yourself ,which is easy.

Spray the throttle plate and let me know if you have other
codes for misfires.

I hope you do not, still have 4 or 5 year old spark plugs
still in that motor. Get them out of there

Clean the MAF Sensor---CRC MAF Sensor Cleaner

Start doing this work yourself. You can not afford a thousand
dollars per visit at a dealer. I as others will help you out.

Posted on Mar 23, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Ford Fusion will not start wiggle wheel flex column in out up down all while working key finally starts what has went bad


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Ford Fusion 2006 2009 WorkSHOP Service repair manual Download

Jul 04, 2016 | 2006 Ford Fusion

2 Answers

Key stuck in ignition in park. Check charging system comes on. Dealership says it might be a fuse.


Key Stuck in Ford Fusion (2006 model) - YouTube

? 1:21
https://www.youtube.com/watch?v=3LVQttFOzGA
Jun 18, 2014 - Uploaded by Jessica East
#Ford #Fusion #Key #ignition #Stuck #FordFusion2006. ... i have a 2006 mercury milan and my key got stuck in there last night,... it to park with a little bit of force. will see what happens next time. good video, nice to know.

Key Stuck in Ignition While in Park

www.2carpros.com/.../2007-ford-fusion-key-stuck-ignition-while-park
Dec 16, 2012 - KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION FORD:2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan

Nov 06, 2015 | 2006 Mercury Milan

1 Answer

Need to know what code 2110 ford fusion 2006 se


P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection help.png Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more: http://helpforcars.net/obd_codes/p2110_2006_ford_fusion.html#ixzz3mV0SayWu

Sep 22, 2015 | 2006 Ford Fusion

1 Answer

Where is the input speed sensor and how do i replace it?


Usually it is on or in the transmission. It should look like the image in the link. http://contentinfo.autozone.com/znetcs/product-info/en/US/wl2/SU11040/image/4

This will indeed be on the transmission held in with one bolt.

Jul 08, 2015 | 2006 Ford Fusion

1 Answer

2006 fusion sedan no side curtins or air bags ,does it still have left and right sensers or just a front senser?


Have a dealer run your VIN #

You can learn all about what your car has
off the assy line

Jul 28, 2014 | Ford Fusion Cars & Trucks

2 Answers

What is error code P0128 on 2006 Ford Fusion SE, 4 cyl, auto


P0128 is the fault code to check 1.the coolant level 2. thermostat defective 3. ECT (engine coolant temperature) sensor defective

Nov 13, 2010 | 2006 Ford Fusion

1 Answer

My 2006 ford fusion check engine light is on and


P0882 - TCM Power Input Signal Low, this is a transmission code, I recommend that you take it to a dealer or qualified transmission shop. Hope this helps.

Jul 05, 2010 | 2006 Ford Fusion

1 Answer

Had injector seals replaced on the car and seens


make sure all the sensers are connected properly, ive repaired va lot of injecter seals due to blow back and there is a lot of stripping involved

Mar 09, 2010 | 2006 Ford Fusion

1 Answer

Moaning, whining sound when the clutch is depressed. Gets louder when revving the engine. 2006 Ford Fusion 4 cyl 5 speed manual. I think it might be the throwout bearing but not sure. Don't know if the...


last one or i will not get up for work tomorrow,its the thrust bearing ,**** plastic fittings used ,when it goes completely ,just renew the whole lot ,if you drop subframe then they are easy to change ,about 2 hrs, but you mush drop the subframe ,its only 4 bolts two either side

Jan 12, 2010 | 2006 Ford Fusion

Not finding what you are looking for?

Open Questions:

See all 2006 Ford Fusion Questions

2006 Ford Fusion Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...