Question about 2003 Kia Rio

1 Answer

How to trace cam shaft sensor in 2003 Kia rio

Posted by John Polgreen on

Ad

1 Answer

toddgilbert

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kia Master
  • 6,360 Answers

There's this website www.reliable-store.com
They have
books on ALL vehicles.
it covers wiring diagrams, electrical diagrams,
fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, owner's/service/repair/parts/maintenance manuals etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

Posted on Mar 18, 2018

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: My 2003 Kia Rio Cinco back hatch latch handle is

We had the same problem.
I took out the bolts outside, then crawled into the back area of the car, and took a screw driver, and slid it along the inner hatch catch, and found the safety latch and released the hatch. Then I took the inside off, and disconnected the handle device from the inside. It was rusted, and broken. I went to Kia, and bought a new one and reinstalled, after greasing the new one up. Took me a while, but they wanted 280.00 in labor, so it was well worth it.
Just be patient and go slow. A good metric socket set will be the best thing, with a regular and phillips screw driver.
Good luck
David

Posted on Jun 24, 2009

Ad
arauzvictor1

Victor Arauz

  • 466 Answers

SOURCE: knock sensor replacement

Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Posted on Mar 19, 2010

roniecon

Ronny Bennett Sr.

  • 6927 Answers

SOURCE: where's the camshaft position sensor on a 2003 kia

On the rear of the head

Posted on Mar 21, 2010

Anonymous

  • 7 Answers

SOURCE: 2003 kia rio- water pumps

If it is your first time having the timing belt changed, chances are the water pump is still in good enough shape to hold out until you are due for your next belt change. No sense throwing away money prematurely...

Posted on Apr 14, 2010

Testimonial: "thanks"

Anonymous

  • 3 Answers

SOURCE: How do I replace the knock sensor on my 2003 kia

On 2003 Kia Rio the knock sensor is located under the intake manifold and must be changed from underneath the car. If you remove the oil filter it is directly above it and is in clear view once the oil filter is out of the way. The connector plugs in behind the intake manifold air breather on the top side. If you remove the air breather cover it will help you get to it. I wish I had someone tell me where it was instead of looking for it for over 2 hours. It is simple after you find it.

Posted on May 17, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

1 Answer

Cam sensor location for a 2004 1.6 4 cyl. Kia Rio


The cam sensor on a 2003 Kia Rio is located on the front, driver's side of the engine, Should be the same on the 2004 ki8a reo's. God-Bless! This is for the 1.6,

May 20, 2015 | 2004 Kia Rio

1 Answer

Camshaft sensor for 2003 kia rio check engine light


Check the wiring, animals love chewing on wires.

May 05, 2013 | 2003 Kia Rio

1 Answer

Camshaft sensor for 2003 Kia Rio causes check engine light


I would guess a wiring issue. Check all the cabling and make sure all connectors are nice and snug with no signs of corrosion or burnt.

May 05, 2013 | 2003 Kia Rio

1 Answer

Can you clean knock sensor on 2003 kia rio


O2 sensors in general are not "cleanable". If they have failed than they are typically replaced.

Do you have a code for an O2 sensor? If so whats the code?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Feb 09, 2012 | 2003 Kia Rio

1 Answer

2008 Kia Rio-After I replaced the timing belt my check engine light came on. I was told that the cam shaft position sensor was bad and needed to be replaced. I replaced it and the check engine light came...


were the codes cleared after replacment if not try that
if they were test the wires for cam signal and check for damaged ---cuts---fraied---pinched

May 28, 2011 | 2008 Kia Rio

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

4 Answers

2003 kia rio- water pumps


I would follow the mechanics recommedations. I think he's taliking about the cam and crankshaft seals. Yes the water pump should be replaced as well. The pump that sprays windshield washer fluid onto the windshield is called the windshield washer pump. The water pump is on the engine and pumps water (coolant/antifreeze) through the engine to the radiator and heater core.

Oct 29, 2009 | 2003 Kia Rio

1 Answer

Torque specs for the cam cradle on a 2003 1.6 kia rio


your post has gone un answered for 2 years. i just stareted last week . as a fellow rio owner im determind to help as many as i can .there are over 5000. un answered kia posts.if you still need help re- post . with any new info. 03 rio's are blue booked at $500

Dec 23, 2008 | 2003 Kia Rio

Not finding what you are looking for?
2003 Kia Rio Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...