Question about 1998 Chevrolet Corvette

2 Answers

Washer fluid doesn't squirt out,

The lines were cleared out, just doesn't dispense washer fluid (tank is full)

Posted by Anonymous on

  • Anonymous Jul 31, 2009

    it seemed like the pump was pumping.

  • Randy Fitz May 11, 2010

    Is the pump pumping when disconnected from the nozzles?

×

Ad

2 Answers

Randy Fitz

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 112 Answers

It may be that the nozzles are clogged, in which case, replacing them is best. The pumping efficiency may have fallen below the neccessary threshold requiring pump replacement.

Posted on Jul 31, 2009

Ad

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 467 Answers

Check the pump for operation, all check the fuse and relays for the washer fluid

Posted on Jul 31, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both the front and back wipers of my 2007 Saturn Vue work, but no fluid comes out, even though it's full, and no sound is heard like it does when out of fluid.


Many possibilities.
Check to see if the electric motor that pumps the washer fluid is working by detaching the hose at the bottom of the washer tank and starting the car & dashboard washing switch ( the multi-switch that controls the washer.)
If you get no fluid squirting out, either the fuse or the washer pump motor is bad.
If it is pumping fluid out there, try hooking a hose to the fluid line and blowing on it to see if fluid will pass through the line, or if it is plugged up ( usually at the nozzle).
If that is clear, perhaps the whole system has lost it's "prime".
Try charging the whole system with water by blowing water from your mouth into the washer lines.
Many cars can lose their "prime" with months or years of dis-use.
God bless your efforts.

Dec 22, 2015 | Saturn Cars & Trucks

1 Answer

I have 2004 envoy .the windshields washer squirting water on front windshield but not on rear .does it have a rear resivory?? What might be the problem


no same tank but two pumps possible clog of line and or nozzle pull hose off nozzle and try to see if fluid squirts if yes use a pin or air or clear nozzle if no fluid possible pump in washer fluid tank shot

Aug 02, 2015 | Cars & Trucks

2 Answers

Rear washer not dispensing washer fluid


Fluid in tank? or does it feed from front tank? Is there a pump in the rear tank? does the pump run? Could be electrical connections or switch problems if not pump motor. If freezing weather is washer fluid freeze proof? if not motor pump may be damaged.

Mar 04, 2015 | 2004 Nissan XTerra

1 Answer

Windshield washer fluid doesn't squirt after filling the resevoir & resevoir is empty later.


Make sure your washer fluid line that goes from the tank to the pump is connected.

Jul 24, 2011 | Ford Taurus Cars & Trucks

1 Answer

Windshield washer fluid lamp will not shut off. It is full. States that i need to add windshield washer fluid and it is full, how do you reset the sensor. ?


sometimes that takes a few starts and stops, if it doesn't clear in a couple of days unhook the battery wait 5 minutes and hook it back up

Jul 11, 2011 | 2008 GMC Sierra 1500

2 Answers

THE WINDSHIELD WIPER FLUID DISPENSER ISN'T WORKING, AND THE PROBLEM ISN'T WITH THE PUMP. I HAVE BEEN TOLD THAT THE COMPUTER IN THE CAR HANDLES THIS FUNCTION AND THE COMPUTER HAS TO BE REPLACED. DOES THIS...


if you can hear the pump running when you hit the washer control you may have either a crimped hose somewhere or the spray nozzles may be clogged .also you might have a clogged hose . try the sprayer with the hood open and if it works , your hose is folding when you close the hood . if it still doesn't work , with hood open , dis-connect the hose at the sprayer . if washer fluid is coming out you can clear out the nozzles with a piece of fine wire .

Mar 09, 2011 | 1995 Mercury Grand Marquis

1 Answer

Winsheild washer wont squirt


Possible bad wiper fluid pump. Remove the washer fluid tank and run a jumper to the positive ( red ) wire on the pump. If the pump runs then it's good and you may have a plugged line. Remove the small rubber hose from the bottom of the tank and try shooting compressed air into it to clear the line of obstructions and then re - install everything, fill tank 1/4 way and test. If it works you'll be good to finish filling the tank !
Hope this helps!

Nov 05, 2010 | 2001 Mitsubishi Galant

2 Answers

The washer fluid warning light is on will not go off after I fill it. How do I reset it?


I have no warning lights on my 2000 SType Jag, but my washer fluid dispensers are not operating. When the lever is pushed, no washer fluid dispnses. Washer fluid well is full. What is the problem and solution? Thank you.

Nov 13, 2009 | 2000 Jaguar S-Type

2 Answers

Windshield washer not working properly


If you have used ANYTHING beside windshield solvent in you reservor, you may have created WAXING from soap in the bottom of washer tank, which clogs pump,lines, and nozzel....take the tank out and wash it..disconnect washer hoses at nozzel and clear with compressed air along with the nozzel...if you use solvent only you may have a worn washer pump or restriction...check those and good luck.....

Jul 04, 2009 | Ford Five Hundred Cars & Trucks

1 Answer

Liftgate washer problem on 2003 Ford Windstar


Yes a shop is usually great advice with this but heres some things you can do yourself. first lets keep it simple have you inspected rear nozzle and cleared nozzle openings with sharp pin?
First you must have these following tools:
haynes or chiltons repair manual
multitester with voltage and impedance features
Step one: location reservoir for washer fluid
Step two: access the sprayer motors under washer reservoir
step three: using multi tester set to 20V test hot leads to motors if theres power then move on if not check fuses and follow power leads to look for damaged power wiring
Step four: if there was power make sure the lines are intact and full of fluid after youve pressed switch (you may have to trace fliud line all the way to the rear for damage or leaks)
After all this you should've been able to find problem theres nothing left once theres power and fluid to rear nozzle except clearing the nozzle openings

Jan 15, 2009 | 2003 Ford Windstar

Not finding what you are looking for?
1998 Chevrolet Corvette Logo

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

john h

Level 3 Expert

23504 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...