How to replace power steering hose - Cars & Trucks

Power Steering Fluid Reservoir Outlet Hose Replacement

Removal Procedure

1. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
2. Remove as much power steering fluid from the remote power steering fluid reservoir as possible.
3. Place drain pans under the vehicle as needed.


Click to Enlarge

4. Disconnect the power steering fluid reservoir outlet hose (1) from the remote power steering fluid reservoir.


Click to Enlarge

5. Disconnect the power steering fluid reservoir outlet hose (1) from the power steering pump.
ImportantDisconnect any clips as needed before attempting removal.

6. Remove the power steering fluid reservoir outlet hose from the vehicle.

Installation Procedure

Hope this helps a little.

How-to: Replacing the power steering reservoir to pump hose - CEG ...

contour.org/.../82138-how-to-replacing-the-power-steering-reservoir-to-...
Jul 3, 2013 - How-to: Replacing the power steering reservoir to pump hose ... to allow air into the suction side of the PS pump, aerating the fluid. ... off the spring hoseclamps from the smaller return hose and the large hose to the pump.
images for How to replace suction and return hoses

How to Remove a Power Steering Hose the Easy way, Tool ...

? 7:49
www.youtube.com/watch?v=OVBFrMcmV7Y
Dec 12, 2013 - Uploaded by Artistry Photography How to Remove a Power Steering Hose the Easy way, Tool Review ... The removal of this power steering pressure hose is a hard job but the ...

Replacing A Leaking Power Steering Hose - YouTube

? 2:38
www.youtube.com/watch?v=l1boEHtawcM
May 12, 2010 - Uploaded by Scotty Kilmer replace the whole hose assembly, they hold 1600 psi pressure, you can't .... i was told i need a new power steering pressure hose for my 2003 .

Power Steering Box Dirty

OK you know the problem but is it something as simple as replacing the Power steering hose or as complicated as also needing a new power steering pump also? Look at where its leaking to determine what needs replacing. Remember it just takes a little time to determine where its leaking. If you find that its not the hose leaking but its the power steering pump then follow these easy steps and save $100s doing it yourself:
1 Remove the negative battery cable with a wrench and place it aside. Remove the upper strut housing tie bar if necessary for access. Remove the power steering serpentine drive belt and electrical plug on the TFE off as applicable. Remove the lower bolt from the mounting bracket using a socket and ratchet if necessary for access. Take off the inlet and outlet hoses from the power steering pump. Remove the reservoir hose only on the supercharged engine. You will need a flat-head screwdriver for this task.
2 Place the power steering pump pulley so the bolts can be accessed through the hole in it. Remove the mounting bolts, using a socket and ratchet, through the hole in the pulley. Take the power-steering assembly out from the bracket. If necessary transfer the pulley to the new pump with a pulley puller.
3 Replace the power steering pulley assembly before you install the pump using the pulley-install tool from your kit. Start the power steering inlet hose connection to the pump by hand. Replace the power steering pump assembly to the engine. Replace the lower bolt first, making sure the hose and heater pipe have enough clearance so they do not touch. If the two rub together they will make noise after the installation is finished. Replace the outlet hose to the pump, directing the hose under the engine harness and the heater hose. If the engine is supercharged it will be necessary to connect the hose from the reservoir.
4 Torque the power steering gear inlet hose to 20 foot-pounds and the hose clamp at the pump to 15 inch-pounds. Torque the pump mounting bolts to 20 foot-pounds. If equipped with a TFE pump, attach the connection. Replace the power steering drive belt or serpentine belt if you removed either. Replace the upper strut tie bar and torque the nuts to 18 foot-pounds. Replace the negative battery cable and fill the power steering reservoir with fluid. Bleed the steering system by starting the engine and turning the steering wheel right and left until all the air is out.

If you notice problem with power steering,the hose has to be inspected,if its faulty it has to be replaced.

=========
For your help,i provide you with few solved helplinks showing how exactly to replace power steering hose:------

How to Remove Power steering Pressure Hose ?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

---------

How to replace power steering pressure hose?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

--------------
These will help.
Thanks.

For procedure to replace power steering hoses,click the link below :----http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html
----------Also its advisable to go through this additional help links.Click the link to go through the procedures:----How to Remove Power steering Pressure Hose?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

Vacuum hose Routing diagram?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-hose-routing-diagram-for-acura.html

Ac line and evaporator drain hose?

http://repairhelpcenter.blogspot.com/2011/10/ac-line-and-evaporator-drain-hose-on.html

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

Vacuum Hose Routing Diagram For Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

How exactly the Vehicles A/C Hose works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-ac-hose-works.html

HOW TO REPLACE AN UPPER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html
HOW TO REPLACE A LOWER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html

Fail smog test due to gas filter hose?

http://repairhelpcenter.blogspot.com/2012/01/fail-smog-test-due-to-gas-filter-hose.html

EGR Hoses melting?

http://repairhelpcenter.blogspot.com/2011/12/egr-hoses-melting.html

EVAP connecting hose to PCV valve Collapse?

http://schematicsdiagram.blogspot.com/2012/01/evap-connecting-hose-to-pcv-valve.html

--------How to replace Power steering rack and pinion gear? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html
--------How to replace Power Steering Pump?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

----------------
How to replace Steering Linkage? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html
-----Car steering wheel makes noise?

http://schematicsdiagram.blogspot.com/2011/12/car-steering-wheel-makes-noise.html

------
Car makes clicking or tapping sound? http://schematicsdiagram.blogspot.com/2011/12/car-makes-clicking-or-tapping-sound.html
---------This will help.Thanks.

It's very easy, undo screw one end from back of power steering pump, no need to remove pump, and unscrew other end of hose from steering gear box, replace hose and top off with power steering fluid, when you undo power steering hose have a pan to catch the power steering fluid that will drip out.

Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

1. Remove the power steering pressure hose (2) from the power steering pump (1).
2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
4. Remove the power steering pressure hose (1) from the power steering gear (3).
5. Remove the power steering hose retainer (2).
6. Remove the power steering pressure hose (1) from the vehicle
   1. Install the power steering pressure hose (1) to the vehicle
   2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
   3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
   4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
   5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.