Question about Dodge Ram

1 Answer

I need some help with the power windows on my 2013 ram i put a new circuit breaker to make my front windows go down but then they dont go up i have to shut the truck off and restart it to bring the windows up and it stops working again i have to the whole routine again frustrated but nothing stops the back windows from going up or down just the front

Posted by martin lemelin on

Ad

1 Answer

Jaye t rock

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 264 Answers

OK so you installed a circuit breaker..... Good for you, hey you need a relay switch to make it work properly. Cheers

Posted on Feb 06, 2018

Ad

5 Related Answers

Anonymous

  • 6 Answers

SOURCE: 2000 Jeep Grand Cherokee Laredo Power Windows

i am a chrysler jeep tech. at a dealership i have seen alot of this in these jeeps 90% of the time the problem is between the driver door and the body open the door there is a rubber tube with wires inside, diconnect this ruber tube from the door pull it back and i would almost promise you will find some broken wires just strip them connect them buy colors solder them together and tape them up and your windows and or door locks will work like new

Posted on Aug 07, 2008

Ad

smoken55

  • 4 Answers

SOURCE: Power windows in front will not go down back windows work

I had the same issue on my '01 530i. The window stayed in one place and I could hear the motor going up and down. It took me 30 mins to fix both the Driver's window and the front Pass window. Remove the door panel, then pull back the plastic liner. There are 2 clamps that hold on to the window. You will need to loosen these 2 clamps (that ride on vertical guides), either find the rubber pads (2 per clamp) that wedge between the glass and the clamp. (one on each side of the clamp.) or purchase new ones. Replace these rubberpads, slide the window back into place. Gently snug up the clamps, and carefully raise the window until it seals. This will set its position. Now tighten up the clamps again. Done. One other issue that sometimes occurs is that there is a plastic clip that needs to be replaced that holds the cable to the clamps, but normally only one clip goes at a time and the window will twist and some times break. That doesn't sound like your issue. Good luck.

Posted on Jan 07, 2009

Anonymous

  • 3 Answers

SOURCE: The engine shut down while on stop and go traffic. Tried to restart but the throttle was weak and shut down again. After shutting everything down for 5 minutes, restarted the engine. The throttle w

If the car is having trouble maintaining idle (the tach dips and car dies) the common causes are the idle control valve and camshaft position sensors. The cam sensors failing will be indicated by a check engine light.

The ICV can removed and cleaned with good results (I think there is a write up on bimmerfest) or purchased new for about $100.

While you are in there check the intake boot that is Y shaped for cracks, it's prone to fail and will mess up your idle too.

read up on the major forums and you'll get more info

Posted on May 18, 2009

Anonymous

  • 8 Answers

SOURCE: Power windows dont work

If all windows stopped workin at once it's a relay ... You can usually find them under your steering wheel ... You more than likely have to remove the panel under the steering wheel and you'll see them... I forgot which one it was but call a BMW dealership ... And let them know what relay you need...

Posted on Aug 24, 2009

Anonymous

  • 1 Answer

SOURCE: 94 chevy s10 blazer power windows not working

I had the same problem - driver side fine, passenger side front not working/slow or the back seat. You need to replace the window motor on the passenger side. Yes, there are two motors. It's pretty simple if you are handy with some tools. The hardest part is getting the 4 mounts that hold the window motor to the door off. The are factory riveted to the door, so I had to grind the outsides off and tap them out. Just watch the spring lever that holds the window bar for going up and down. I didn't pay attention and it snapped back - nearly broke my thumb.

Dani-Lynn

Posted on Oct 05, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 4 runner power window fuse location


There is a 30amp circuit breaker. They reset automatically after a while. When the motors start to go bad, they don't raise the windows fast, and they can throw the circuit breaker. Figure out which motors are struggling and replace them.

0900c15280061106-jnh1p0frnkt3q2fbcpfimq4v-2-0.gif

Aug 14, 2017 | 1995 Toyota 4Runner

1 Answer

My power seats and only the power windows on right side quit working on my 2007 silverado classic lt1500 I replaced the circuit breakers already and it did not fix the problem


Does you truck have Memory Seats ? There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function.
If you replaced the circuit breaker , did you check for B+ voltage at the switch ? If you have memory seats there is a control module that is in the mix.
For the power windows same thing here ,the BCM - body control module is involved .A factory Tech 2 scan tool is still the best tool to use ,checking data parameters .
The switch for the front passenger power window has 2 positions UP and DOWN, and it's position is a direct input into the PDS. Upon receiving a request for power window operation (switch activation), the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to drive the window UP or DOWN.
The front passenger power window can also be operated from the driver master control. The front passenger window switch on the driver master control has 2 positions UP and DOWN and it's position is a direct input into the DDS. Upon receiving a request for front passenger power window operation, the DDS transmits a GMLAN message indicating the changed switch position. When the PDS receives this message, the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to move the window UP or DOWN.
GMLAN - is a data bus communication network that vehicle modules talk together on.
Rear Passenger Power Window Operation (RPO A31/AN3/DL3)
The body control module (BCM) monitors the window UP/DOWN command from the DDS. When the rear window UP or DOWN command is received, the BCM sends a signal to the appropriate rear window switch. The rear window switches continuously monitor the up and down signal circuits, if no function is being commanded, the signal voltage is at approximately B+ voltage. If the UP or DOWN function is commanded, the BCM signal voltage drops approximately 5 volts and the appropriate rear window switch will then command the window in the UP or DOWN direction.
Your best bet would be to take your truck to a GM dealer !
Your best bet

If

Nov 04, 2015 | Cars & Trucks

1 Answer

I need an electrical diagram showing wiring from the base,to power windows on a 2003 Chevrolet Venture,my power windows won't work either side in my 2003 Venture,checked power at fuse box next to...


Check the main fuse box next to the battery, # 8 max fuse powers IGN MAIN 2 Ignition Switch to Fuses (I/P): BCM PRGRM, FRT HVAC LOW/MED BLWR, FRT WPR/WSHR, HVAC/DRL, MALL/RADIO/DIC, PWR QRT VENT, RR HVAC, RR WPR/WSHR, SWC ACCY & PWR WDO Circuit Breaker.

#3 circuit breaker is the front window breaker, try swapping it out with another breaker beside it and thats located in the side dash panel also.

The common cause of failed power window function is the switch on the doors going bad from dirt. Does the power window on the passenger side go down with the passenger side switch?? if it does then its a bad drivers side and and try cleaning the switch with electrical contact cleaner. 95% of the time this will save you from buying a new switch.

keep us posted and thanks you for using fixya

Nov 01, 2011 | 2003 Chevrolet Venture Passanger

1 Answer

My 2002 jetta the door didnt lock or unlock and windows dont work and alarm is off


I appologize for not getting back to you sooner. The market place is still in developement and for some reason this afternoon when I tried to comment I could not post from my android, Ipod, or Ipad.

The only thing the two have in common are fuse 38 and the power window circuit breaker. This would be a good place to start. The fuse will be obvious if it is blown. You will need to check continuity of the circuit breaker or swap it with one that you know is good.

If the fuse and circuit breaker are good than you will need a test light or multi-meter. You will also need to remove the drivers front door panel to gain access to the power window switch and the drivers front door module. If you have this test equipment and are able to get the door panel off let me know and we will go to the next step.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 08, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

MY 2006 DOdge ram Thunder Road's windows dont work. They used to work i bought the truck new. All of a sudden all the windows from every control dont roll down their own windows as well as the driver side...


your truck also has power relays working with the fuses. each door has its on circuit except the main controller in drivers side door. if u cannot control anything from drivers side then look at the relays for possible cause to your problem.

Apr 22, 2010 | 2006 Dodge Ram

2 Answers

98 buick century power windows dont work


CHECK POWER WINDOWS 20 AMP CIRCUIT BREAKER.

Jan 24, 2010 | 1998 Buick Century

1 Answer

Power windows dont work replaced circuit breaker no result


you need to check for power at the window switch,if you have it there,check for power when you rock the switch down then check for power up.

Nov 21, 2009 | 2003 Oldsmobile Alero

2 Answers

My front power windows dont roll back up and i already replaced the circut breaker what can i do to roll them back up


You will need to replace the window motors. Let me know if you need further info or feeling like doing the procedure

Aug 28, 2009 | Oldsmobile Alero Cars & Trucks

3 Answers

Power steering


transmission range sensor needs changing $74 brand new from napa
mine broke and the radio,windows and power steering stopped working put new sensor on worked perfect,


until i took it to oil can henrys to have a transmisson flush please dont have that done or you will have to replace the whole gear box

Jun 23, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...