Question about 2002 Isuzu Rodeo

Open Question

How to remove front bumper on 02 rodeo - 2002 Isuzu Rodeo

Posted by Randy Wilson on

Ad

4 Related Answers

MrScary66613

Travis Humphries

  • 1990 Answers

SOURCE: How do you remove the front clip of 02 x type jag.

That Means the Entire Front End. Please Rate my Solution, I need all the Help that I can Get! Thanks!

Posted on Jan 29, 2009

Ad

Joe Hogan

  • 10865 Answers

SOURCE: front bumper removal

all you have to do is unbolt it. if the nuts won't budge spray them with wd40 and wait over night for that product to loosen up the rust.

Posted on Sep 14, 2009

Ad
honeymokey

honeymokey

  • 3113 Answers

SOURCE: how to remove 1993 rodeo front bumper

http://www.myisuzuparts.com/showparts.php

Posted on Dec 26, 2010

headstrong56

headstrong56

  • 493 Answers

SOURCE: 99 blazer front bumper removal

crawl under the front of the blazer. the bumper should be bolted to the frame itself. usually 2 on each side.

Posted on Jul 15, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove front bar 2004 rodeo


you need to take off the 6 bolts on the bottom of the bar under the bumper ok

Oct 25, 2015 | Cars & Trucks

Tip

How To Install Replace Front Bumper Cover Honda CR-V 02-06 1AAuto.com


How To Install Replace Front Bumper Cover Honda CR-V 02-06 1AAuto.com

on May 10, 2012 | 2002 Honda CR-V

1 Answer

My hood will not latch all the way shut for my 99 rodeo


There are two rubber grommets located on the hood-one at each front corner. There are replacements that can be purchased at parts stores (Help brand-usually on those "spin-around-racks"-just ask parts guy you want hood bumpers. These come in different sizes (diameters)-the ones I found and used were a bit small. I used silicone to "fatten" them up. You will see they are adjustable by threading (rotating" them in the hole in your car's hood. What seems like your hood not latching is the hood is not held tight against the latch (constant pressure from the bumpers holding hood up). Your hood is just laying all the way down-you need the bumpers.

Apr 07, 2010 | 1999 Isuzu Rodeo

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

VW SHARAN 02. i need to remove the headlights so i can straighten the cap covering the bulb and also the light tilter is not working ( the switch does not seem to tilt the beams when i turn the dial, this...


  1. In order to remove the headlights, you need to remove the front bumper cover.
  2. Place the front of the car on jack stands.
  3. You will need to remove the screws on each side in the fender wells on the back side that screw into the bumper. these are torx screw head type.
  4. On the underside of the car there are larger torx type screws that attach the bumper cover to the body. They need to be removed.
  5. You will need to remove the grill that has the VW symbol on it. Under the grill there is more torx type screws to remove. Inorder to remove the grill you need to get the hood release rod off as well.
  6. With the bumper cover removed, there are four torx type screws holding the headlight in place. Once removed you can unplug them and the head light is off.

Jan 25, 2010 | 2002 Volkswagen Jetta TDI

1 Answer

Air conditioning filter


left hand side of vehicle behind grill and front bumper bar (receiver drier/filter) for air conditioning refrigerant.

Jun 11, 2009 | 1998 Isuzu Rodeo

2 Answers

Saab 93 bumper removal


It depends on what year your car is,

If it's the pre 02 car then inside the boot there are 2 M10 nuts near the tie down eyes, remove these and then pull the bumper tips outwards whilst pulling the bumper rearwards.

If its the post 02 car then remove the torx screws inside the wheelarch 2each side, remove screw from bottom edge of bumper near to wheel arch each side, remove 2 plastic nuts from lower bumper near spare wheel well, remove rear light clusters then remove the screws behind them, unclip ends of bumper from bodywork and pull rearwards.

May 22, 2009 | 2008 Saab 9-3

1 Answer

How do you remove the front clip of 02 x type jag.


That Means the Entire Front End. Please Rate my Solution, I need all the Help that I can Get! Thanks!

Jan 29, 2009 | 2003 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

443 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14846 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...