Where is the ignition relay switch located in a Honda CRV 2006?

The '03 Honda CR-V has two main relays; PGM-FI Main Relay 1 and PGM-FI Main Relay 2. Both main relays are located behind the right side of the dashboard near the glove box. After the glove box is removed, you should see two rows of relays. The main relays are in the row closest to the glove box at the far end towards the driver's side. Based on my experience, it would be very abnormal for even one of these relays to have failed let alone both. If there is a power distribution problem I would lean more towards a possible electrical ignition switch failure as this is fairly common in these older Honda vehicles. You can read more about ignition switch failure symptoms here: https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-ignition-switch

Question edited to put both questions into one. Extra one deleted. To see your question posted, you have to Refresh the page.

Fuel cut off switch 2007 honda crv - Fixya

https://www.fixya.com > ... > Honda > CR-V
Nov. 15, 2019 - the fuel cut off switch is located behind the center console on rh vehicles,right behind the ashtray. Posted on Apr 30, 2009. 2.
Where is the fuel cutoff switch on 2000 Honda crv - Fixya
Nov. 4, 2018
WHER IS THE FUEL CUT OFF SWITCH ON 2002 HONDA CRV
Nov. 20, 2019
2007 honda crv fuel cut off switch - Fixya
Nov. 21, 2019
SOLVED: Fuel cut off switch location Honda 2005 Civic - Fixya
Sep. 6, 2019
More results from www.fixya.com

There are videos here

https://www.google.com/search?q=2006+Honda+CRV+diesel.+Where+is+fuel+cut+off+switch

..

Fuses and relay Honda CR 2002 2006

not herd of them all getting the same fault at same time but it could be the master control switch or the tamper/control unit would think it would be the switch.

at all stations?
all fuses, in both boxes. (did you read the operators guide to find them,
some cars have a circuit break (thermal) for windows,
and is located in the fuse box.
all this info is at alldata.com
ill look. ill respond , as you are a pro DIY person, can read schematics. if not , its just a guessing game.
IT IS a FUSE, not a breaker. but each motor in door has CB.
UNDER HOOD 40am Fuse #13
then fuse 23 underdash and fuse 8 same.
then the relay.same place.
and the relay is controlled by, master station (drivers)
the driver location doesnt need the relay to work.
the relay feeds power to all other window controls
so the master station is unique.
log in to alldata.com and see the pages on power windows.
here are some tid bits.
battery pull warning

Resetting the power window control unit is required after performing the following procedures: Disconnecting the battery, Removing the No. 6 (7.5 A) and/or the No. 23 (20 A) fuses from the under-dash fuse/relay box or disconnecting the driver's door wire harness.
and
window relearn/reset.
Control Unit Reset

1. Turn the ignition switch ON (II).
2. Move the driver's window all the way down by holding the driver's switch firmly down; when the window reaches the bottom, hold the driver's window switch firmly down for 2 seconds.
3. Move the driver's window all the way up by holding the driver's switch firmly up; when the window reaches the top, hold the driver's window switch firmly up for 2 seconds.
4. If the window does not work in AUTO, turn the ignition switch OFF and repeat the procedure.
5. Check the window and power door lock operations

it is the same relay. You can hear it click when you turn on hazards. Just listen for the sound and you will locate it.

check the beam lights relay,

JUST POP SWITCH OUT AND BULB GOES INTO SWITCH USE SMALL SCREW DRIVER TO REMOVE YOU WILL HAVE TO TWIST IT COUNTERCLOCKWISE TO REMOVE, TWIST CLOCKWISE TO INSTALL.

you should start by checking fuses,switch located on door pillar where door hinges are.sounds like a blown fuse or bad beeper,

Ok,
1. ensure ignition off
2 . bridge the 2 pin connector, Put a piece of wire across both terminals
3.switch ignition on
4. SRS lamp should illuminate for 6 seconds
5.disconnect the bridge wire within 4 seconds of the warning lamp extinguishing
6.SRS lamp should illuminate 2 times, Codes erased
7.switch ignition off
8 Wait 10 seconds. switch ignition on and check SRS warning lamp operation.
hope this helps