Outside mirror moving, is there a pin broken inside is it easily replaced?

Power Dr Mirrors Diagnosis & Testing

Removal & Installation
Motor

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove or disconnect the following:
   
   Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror
   
   

   Fig. Removing cover trim and nut
   Removing cover trim and nut
   
   

   Fig. Removing mirrored glass from assembly
   Removing mirrored glass from assembly
   

3. Remove the mirror glass:
   1. Fold the mirror glass forwards and inwards as illustrated.
   2. Grasp and pull the mirror glass lengthways until it releases.
   3. Work the glass out.
   
   
4. Remove electric motor:
   1. Remove the 3 screws from behind the mirrored glass.
   2. Separate the connectors
      NOTE Remember the positions of the connectors.
      
   3. Remove the mirror motor.
      
      

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor

   
   

To install:

1. Install or connect the following:
   
   The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door
   
   

   Fig. Reattaching mirror and electric motor connectors
   Reattaching mirror and electric motor connectors
   

2. Install or connect the following:
   
   The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable
   

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

Use a small pry bar and pry up on the outside edge of the mirror to dislodge it from the center hub. Be careful not to lift up the mirror too high or the drive pins may unseat from the mirror motor pack.

Use a small pry bar and dislodge the heads of the bottom and inside pins from the back of the mirror.

set the factory mirror on a clean flat surface. Use a small pry bar and remove both friction pins from the back of the factory mirror.

Use the closed end of a 10mm box wrench and seat the friction pins in the top and outside holes on the back of the new mirror.

Also I suggest review this reference guide

I hope helped (reember rated this help) Good luck.

Normally u can change the mirror assembly rather easily.even with the outside mirror there is a molding piece on inside.remove.behind is 3 bolt holding that mirror bracket on the out side.if power mirror disconnect plug. go to your local salvage yard or call around for a replacement. hope this helps

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

To repace the COMPLETE MIRROR UNIT, the inside door trim must be removed. Hope this helps

I researched the maintenance manual. The fuse you need to replace is fuse 20 in the under dash fuse box. It controls side windows, washer motor, rear view dim function, and possible seat memory. There are a couple that link to the mirrors, but this is the one for this problem.

check behind the mirror glass there are little plastic rods that are easily broken when mirror gets hit or moved manually. mirror should pop out when pulled carefully by one of corners. be careful not to put to much pressure on the glass when pulling outward

It is a stuck motor. Water gives rust inside housing. Remove mirror and clean motor and components. This is a well known error for H2 mirrors.

You will need to remove the triangular panel on the inside of the door on the opposite side of the broken mirror. Once you remove the panel, you will see the retaining bolts holding the mirror in place. Once you remove the bolts, the mirror can then be pulled out from the outside. Reverse the procedure to reinstall the new mirror.