Question about BMW 328i

1 Answer

E46 328i year 1999 diagram for e box fuses

Load for every fuse

Posted by Stephen Stephen on


1 Answer


  • Level 1:

    An expert who has achieved level 1.


    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.


    An expert that has over 10 points.

  • Contributor
  • 16 Answers


Fuse 1 - 30A - DME, Injectors, SMG Hydraulic unit
Fuse 2 - 30A - DME, Idle control valve, Fuel tank ventilation valve, Fuel pump
Fuse 3 - 20A - E-box fan, Transmission RPM sensor, Camshaft positioning sensors, Mass airflow sensor, Fuel pump relay, Secondary air pump relay, A/C Compressor relay, Fuel tank leakage diagnostic module, SMG selector lever
Fuse 4 - 30A - Oxygen sensors and oxygen sensor heater circuits.
Fuse 5 - 30A - Fuel injector relay.

Posted on Jan 07, 2018


5 Related Answers


  • 13 Answers

SOURCE: I need a Fuse box diagram for a 1999 Ford Contour

do a google search and that should tell you where to get one from or try a junkyard or maybe the ford company can help.

Posted on Jul 23, 2008



  • 19396 Answers

SOURCE: fuse box diagram peugeot 206

Check the website below:

Peugeot 206 Fuses.

Posted on Mar 28, 2009

Steeler Ed

  • 130 Answers

SOURCE: fuse box diagram

Here you go. Start on page 181.

Posted on May 03, 2009


  • 30 Answers

SOURCE: Fuse box diagram is not on the cover of the box on

This is the same location as your car img1972uk6.jpg

Posted on Sep 21, 2009


  • 1 Answer

SOURCE: Lost Fuse Box Diagram - Altima 2005 2.5L

i need to know what ENG CONT AND ENG MTG means on the fuse box of my 2006 altima.

Posted on Jan 14, 2010

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 Silverado instrument lights & tail lights out

Did you check any fuses? Not only check fuse, check fuse circuit for voltage, use a test lite. If you jump load side of park lamp relay, do the lamps come on? The load side is terminal 30 and 87.
park lamps-ytwzgkd30xtrj1x23ml1mrsc-3-0.jpg

Mar 05, 2017 | Cars & Trucks

1 Answer

2004 pt cruiser keeps blowing fuel pump fuse,replaced fuel pump, no change.runs rough at idle and stalls,blows fp fuse,also replaced ign.coil,plug wires and plugs also changed relays

There are two fuses for the fuel pump relay. One fuse is load side of relay, that fuse also sends voltage to load side of asd relay, the asd relay sends voltage to several systems, two of which are the fuel injectors and ignition coil. I'm not telling you to replace, anything, but, you need to do some testing.
The other fuse goes to control side of relay, smaller amp fuse. I don't know the amp rating of the fuse that keeps blowing.
See that fuse, it supplies voltage to load side of fuel pump relay and also to asd relay.

Oct 22, 2016 | 2004 Chrysler PT Cruiser

1 Answer

2006 Subaru Tribeca cd player will not load cd's. When load button is pressed nothing happens......the lights do not come on or anything

I would first check the fuse, if you look in your owners manual it will tell you where the fuse box is. On he fuse box cover it will tell you the radio/cd fuse log a tion.

Apr 03, 2015 | Subaru Tribeca Cars & Trucks

1 Answer

I have a 2004 beetle and i lost my headlights, fog lights, horn, wipers, rear defrost and traction control.

Check All Fuses In Fuse Bracket (at battery) Especially Fuse 176 (110amp)--It Powers Load Reduction Relay--In Thirteen Position Auxiliary Panel- Behind Left Side Of Dash--Integral With Relay Panel. Load Reduction Relay Powers Everything That Is Not Working.

Apr 02, 2015 | 2004 Volkswagen Beetle

1 Answer

Why does 20 fuse plugged into 16 fuse hole spark and blow.

It is doing its job(blowing when there is more current flowing than there should be). What circuit is that fuse in? Whatever the load is(light switch, radio, etc) has an internal short or the wiring between the fuse and the load is shorted to ground. Also never replace the fuse with one that has a higher current rating. That's when you start melting wires and other things that you don't want to melt. Good luck!

Jul 29, 2014 | 1997 Ford Crown Victoria

1 Answer

What causes blown fuse on interior lights on 2008 maxima?

short to ground before the load, the installation for the wire could be worn out so therefore it could be receiving more load current than needed which could result in a blown fuse. poor installation

Nov 18, 2012 | 2008 Nissan Maxima

1 Answer

My 02' mdx won't come out of park, keep blowing a 20 amp fuse. This fuse controls the Cruise, break lights, memory seat, horn and linkage. I have to manually delink. I have unhooked the comand...

Here is an idea, when do you blow the fuse key on, key on engine running, key on engine running hitting the break pedal? Try and get the key on without blowing fuse if possible, then one at a time try those circuit loads ie: horn, brake pedal and so on, if you isolate which load is pulling to many amps(blowing fuse) unplug that load itself, then restart testing, see if fuse stays ok. You can also substitue the fuse with a circuit breaker and unplug each load until click(of breaker) stops.

May 17, 2011 | 2003 Acura MDX

1 Answer

Keeps blowing "ign. run start

load is measured in amps not ohms.ohms is a measure of resistance in a circuit.check the under side of the pdc for corroded wires or shorted wires on the load side of the circuit.

Apr 20, 2011 | Chrysler Concorde Cars & Trucks

1 Answer

Fucs keeps blowing out on 1977 blazer

It depends what the fuse is powering and how or what your doing when it blows. Does just a few things stop when the fuse is blown. Say brake lights and turning signals for example. Then try to figure out how to disconnect part of whats a load on that fuse. Say unplug or remove half the load. If the fuse still blows then you can determine that whatever is off, is not the problem, and whatever you left connected is. Slow process of elimination. IF your blowing a main fuse thats powering other fuses then use the fuse block itself to troubleshoot with. But thats harder because the small fuse will likely have blown first. IF a main fuse is feeding smaller fuses, pull all the smaller fuses, replace the main, and then install the smaller ones one at a time until it blows again. Whatever just blew the fuse is the short. IT's probably better to use an volt/ohm meter and measure the resistants to ground. Low resistants is the short. First remove the fuse,, power up the circuit, Carefully measure the voltage to ground. The side of the fuse that has voltage is the source or battery. The opposite side is the load. Now remove power, measure the load side to ground. Look for low resistants. Remove or disconnect bulbs or what ever the load is. When the resistants jumps up or high, then you found your short.

Jan 25, 2011 | 1983 Chevrolet Blazer

1 Answer

Blown fuse

Replace the Fuse with same size. See if it happens again. If it does figure out was on or off. Try to disconnect part of the load and replace the fuse again. If it still plows then discount some more load. If it does blow then re-connect the loads one at a time, When it blows then you know what load it was. Possible short in the cable somewhere between can be very hard to locate. Another way may be to place ohm meter across fuse and remove loads if the resistants is low, until it goes high. Always disconnect the battery first.

Jan 14, 2011 | Ford E-350 Super Duty Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

702 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts


Level 3 Expert

3063 Answers

old marine
old marine

Level 3 Expert

2312 Answers


Level 3 Expert

501 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides