1998 chrysler town and country mini van how do you replace powersterring pump and change pully

SOURCE: oil pump replacement

This MAY seem Strange But It IS ALL necessary for Oil Pump Replacement. And Please Don't Forget to Rate Me as Most Folks Do Not. Thank You and GOOD LUCK with the Oil Pump Job Also


OIL PUMP
It is necessary to remove the oil pan, oil pickup and chain case cover to service the oil pump rotors. The oil pump pressure relief valve can be serviced by removing the oil pan and oil pickup tube. Refer to Timing Chain Cover Removal and Installation for procedures.

DISASSEMBLY

1. To remove the relief valve, proceed as follows:
2. Drill a 3.175 mm (1/8 inch) hole into the relief valve retainer cap and insert a self-threading sheet metal screw into cap.

1. Clamp screw into a vise and while supporting chain case cover, remove cap by tapping chain case cover using a soft hammer. Discard retainer cap and remove spring and relief valve.
2. Remove oil pump cover screws, and lift off cover.
3. Remove pump rotors.

1. Wash all parts in a suitable solvent and inspect carefully for damage or wear.

1. Assemble pump, using new parts as required. Install the inner rotor with chamfer facing the cast iron oil pump cover.
2. Tighten cover screws to 12 Nm (105 inch lbs.).
3. Prime oil pump before installation by filling rotor cavity with engine oil.
4. Install chain case cover. Refer to Timing Chain Cover Installation.

1. Disconnect negative cable from battery.
2. Remove timing chain cover.

1. Disconnect negative cable from battery and remove engine oil dipstick.
2. Raise vehicle on hoist and drain engine oil.
3. Remove bending brace to transaxle attaching bolt.
4. Remove bolts attaching dust cover to transaxle housing. Lower dust cover to gain access to oil pan bolts.
5. Remove oil pan screws and remove oil pan.

1. Clean surfaces and apply a 1/8 inch bead of Mopar (R) Silicone Rubber Adhesive Sealant or equivalent, at the parting line of the chain case cover and the rear seal retainer.
   1. Use a new pan gasket.
   2. Install pan and tighten screws to 12 Nm (105 inch lbs.).
   3. Install dust shield and bending brace to transaxle housing.
   4. Lower vehicle and install oil dipstick.
   5. Connect negative cable to battery.
   6. Fill crankcase with oil to proper level.

SOURCE: Where is the neutral safety switch located on 1998 Town & Country

THE NEITRAL SAFTEY IS LOCATED ON THE DRIVERS SIDE OF THE TRANSMISSION WHERE THE SHIFTING LINKAGE HOOKS TO AN ELECTRICAL SWITCH THIS SWITCH CONTROLS ALL FUNCTIONS
REVERSE LTS, NEUTRAL SAFETY AND OTHER ITEMS

SOURCE: CHRYSLER town and country mini van turn signal/flasher

I have a 2005 Chrysler T&C. The turn signal would not work at all or activate incorrect side. The switch is easy to remove as described by dukecityman.

Once the switch is of, it has four screws holding it together.I took this apart to find that there was a circuit-board which was contaminated with dirt. wiped it of, put it back together, working fine.

If you take it apart use caution. there are parts on the "top" which will fall out. ( they go right back in) The circuit-board is on the "bottom" half. You really only need to take this part off. (less moving parts)

Your going to replace it anyway, whats the harm?

SOURCE: What does code p0032 mean in a 2004 chrysler town

Heater control circuit high, bank 1 sensor 1. Sounds like your O2 sensor in bank 1 in front of your convertor is bad.

Jose Cada

• 3530 Answers
• Posted on Sep 13, 2010

SOURCE: how to replace starter motor

Hi. Here is the procedure. Jack the car up,secure good with jack stands,block wheels and parking brakes on.Disconnect battery terminal,use 15mm wrench and 15mm socket,remove 2 bolts through transmission bell housing,remove nut from battery cable to starter,disconnect small wire to solenoid

If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...