Question about Chrysler Cars & Trucks

1 Answer

2015 Chrysler 200. Changed battery now the car will start but it won't shift into any gears and the neutral light flashes and accerator won't rev up

Posted by Jason Adamson on

Ad

1 Answer

Arnie Burke

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 7,015 Answers

Unhook batt again fora minute. Now let computer relearn aftr restartin..can take awhile on older cars..jus leave car b

Posted on Nov 04, 2017

  • Arnie Burke
    Arnie Burke Nov 04, 2017

    Unhook batt again fora minute. Now let computer relearn aftr restartin..can take awhile on older cars..jus leave car b

  • Arnie Burke
    Arnie Burke Nov 04, 2017

    Unhook batt again fora minute. Now let computer relearn aftr restartin..can take awhile on older cars..jus leave car b

×

Ad

5 Related Answers

Anonymous

  • 40 Answers

SOURCE: My '01 Mustang V6 revs high when in neutral/when changing gears.

sounds more like the IAC, Idle air control valve.. they can be cleaned with carb and choke cleaner gently...

Posted on Nov 24, 2008

Ad

Anonymous

  • 2920 Answers

SOURCE: 1998 Chrysler Sebring JXI V6 2.5L Transmission Problem

it sounds like the transmission solenoid or possibly the transmission itself trying to go out

Posted on Jan 15, 2009

emissionwiz

Marvin

  • 85239 Answers

SOURCE: 1998 Chrysler Sebring JXI V6 2.5L Transmission Problem

most likely a valve body or a shift solenoid issue, but at the very least the trans pan and valve must come out and or be replaced, those 2 parts are fairly expensive, but don't know how much and don't wish to mislead you, have the shop look at it, u can always decline the repair.

Posted on Jan 15, 2009

Anonymous

  • 49 Answers

SOURCE: OIl pressure light flickers

change the oil pressure switch or the wrong oil

Posted on Jan 18, 2009

jmgldsmth

Jim Goldsmith

  • 2005 Answers

SOURCE: Chrysler 3.5 won`t rev past 2500 rpm?

remove the aircleaner intake hose and, check the intake air control flap for free movement

Posted on Apr 22, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 04 envoy slt xl won’t start none of gages work only battery light comes on, has full battery tho & won’t shift out of park

Try stepping on the brake when trying to shift with the key on. Then try starting im neutral or other gears to see if the neutral safety switch is bad in park. You may have a bad wire from the battery to power distrubution or bad ground. So many things it could be.
0helpful
1answer

2015 Chrysler 200 the car will start but it won't shift into any gears and the neutral light flashes and accerator won't rev up

You need a scanner hooked up to see what is going on. Sounds like the transmission has gone south.
0helpful
1answer

My rpm rev's past 3 car stalls then shifts...sometimes won't shift

Due for a transaxle rebuild,common on that veh

The fact you continued to drive it when it won't
shift correctly & has been slipping, your done
1helpful
2answers

I have a 200 saturn and every once in a while it won't turn over...battery fine and no engine light

If it is an automatic shift you should have a neutral safety switch between the key switch and the starter. I would check that and for power at the starter when it fails to crank.
If it is a manual shift there is a switch on the clutch pedal or linkage.
It may be tough to find until you can duplicate the problem on demand.
Could also be a dead spot in the starter or solenoid.
0helpful
1answer

Won't shift properly

Your probably pulling OBD Code P0758, just like mine is. Ive changed the trans in a customers car now 3 times with the same result. Hard shift into rev and 2 but no third gear. I believe its the TCM or wiring harness. Check to have the TCM Completely flashed and re-written by the dealer, this may help, if Not replace the TCM is my only other options, because I do not believe that 3 transmissions have been bad.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/samuel_4e847b1ae10ff587

0helpful
1answer

2001 Chrysler Concorde - Changed the shift CABLE AND ****** FLUID and now it does not want to engage into gear and the reference lights (Park, neutral , drive etc.) are not stable. They flash back and...

Something is wrong with your park shift interlock holding the key in. Your gear selector isn't reading the gears correctly because car don't know what gear it's in.
0helpful
1answer

Chrysler 3.5 won`t rev past 2500 rpm?

remove the aircleaner intake hose and, check the intake air control flap for free movement
1helpful
1answer

2007 chrysler town & country 3.3

If it is always shifting firm, I would suspect it is in the control. Perhaps the computer needs to be flashed at the dealer. A line pressure reading should be done to verify the pressures are correct.
0helpful
1answer

Wont turn over,all shift indicator lights on,engine light on

Scan for transmission faults it needs to see the neutral switch input for it to start
Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

511 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15000 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...