That sensor is located on the transmission near the RH axel. 10mm bolt secures it. It's a 'Hall" sensor. When replacing, remember to reinstall the horse-shoe clip which retains the gear to it.

Posted on Oct 10, 2010

Paul McGrath

776 Answers

SOURCE: installation for compressor

Assuming you have HVAC experience and are licensed to perform this service, you'll first need to recover the R-134A refrigerant from the system (if there's any in it). If there isn't, you'll still have to vacuum before recharge (w/refrigerant & PAG oil). Is there a compressor presently installed?
If so, you'll need to recover any existing refrigerant. Then disconnect the High & Low pressure tubes from the compressor.
Remove the A/C drive belt
Remove the wire harness connector to the compressor magnetic clutch
Remove the 4 12mm bolts which mount the compressor to the engine
Raise the vehicle & remove the FR wheel, plastic splash guards (RH & lower - below the oil filter).
Raise the engine so to increase/clear space for removal of the compressor.
Installation of 2nd compressor is in reverse order.

PS. Some technicians perfer to remove the compressor from the top (requires removal of the radiator cooling fan & the alternator). Some have also removed the LH Exhaust Manifold to make it easier to reinstall the alternator & compressor.

Posted on Oct 10, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

I have found po1191 witch sensors code I song no please help me

P1191 Hyundai ETS Limp Home Valve On

Dec 01, 2015 | Cars & Trucks

1 Answer

I have 2 codes...P-1191, and, P-1193....what are the problems and how to repair

What make , model an year vehicle do you have ? These codes could mean different things for different vehicles ! P1191 Hyundai ETS Limp Home Valve On P1191 Key Line Voltage

May 24, 2015 | Cars & Trucks

1 Answer

My 2004 Xg350 is stuck in limp home mode.

code p1155 refers to electronic throttle system (ETS)- malfunction===causes --wiring--ETS limp home valve

code p1193 refers to ETS -limp home valve --on===causes --Low RPM
code p0302 refers to cylinder 2 misfire detected===causes--engine mechanical fault--wiring---ignition/ fuel system---injector---ECT/MAF sensor---ECM.
Pulling a battery lead to reset is a waste of time as it corrupts the CPU program. Use a code reader to reset . It is quicker and doesn't run the risk of program corruption

Dec 21, 2013 | Hyundai XG350 Cars & Trucks

1 Answer

Our Hyundai, 2002 XG 350 has a P1191 code that comes up, the car will run rough and sounds like it wants to cough when you start to push down on the gas pedal. We have replaced the plugs and three wir

The engine valves are not being opened and closed properly due to the worn gear and missing teeth. Needs to be replaced.

Apr 11, 2017 | 2002 Hyundai XG350 L

1 Answer

Our Hyundai, 2000 XG has a P1191 code that comes up, the car will run rough and sounds like it wants to cough when you start to push down on the gas pedal, I don't see any code #P1191 could you pl

The 350 code is a circuit problem with the coils and the variable valve gears being stripped can be a definite driveability issue .

Apr 11, 2017 | 2001 Hyundai XG300

1 Answer

What does code P1154 mean on a hyundia sontona 2002

You sure that's the right number?
For Hyundai, it shows codes 1151 and 1155, both referring to the electronic throttle system (ETS). I did not find a code P1154.

P1151: ETS Main Accel Position Sensor 2 Malfunction.
P1155: ETS Limp Home Valve.
P1174: Electronic Throttle System #1 Close Malfunction.

Dec 16, 2011 | Hyundai Cars & Trucks

2 Answers

[email protected] to fix dtc p1178 and p1118 on a 2002 hyundai xg350

I live in Australia & have a Hyundai Grandeur XG 3LT V6 2002 model (US equivalent is Hyundai XG300).
Fault codes are P1118 (ETS motor fault) & P1178 (ETS motor battery voltage open). An intermittent fault.
The first code denotes general area of the fault & the second code denotes the specific fault.
So the specific fault is that the ETS-PCM computer is not receiving 12V on pin 2 with ignition on.
'Check engine' light remains on & car is in 'limp home mode' with very little power & poor performance.
I had purchased the Hyundai service manual online (ebook about $8) for the US model. Could not find any
manual for the Australian model. On page FLA-52 found the block diagram for the whole ETS system.
I am a retired electrical engineer so now it became easier for me to find the fault.
There are 2 computers behind the center console. PCM & ETS-PCM.
Pin 2 of the ETS-PCM should have 12V present when ignition is on.
In fault mode 12V was not present. This 12V is supplied from ETS 15A fuse (fuse box under dashboard)
via a relay (i will call this relay the ETS relay). The 15A fuse was OK but the 12V was only
intermittently being passed through the relay points. Relay is located near ignition switch on a
sub panel which has about 6 relays on it. ETS relay was at right bottom corner of sub panel.
Yellow wire feeds the 12V (which is always present even with ign. switch off) to the relay points.
White wire is the output wire from the relay points which feeds 12V to pin 2 of the ETS-PCM computer.
Measure if 12V is present at white wire when ign. switch is turned on (no need to start engine)
I only had the 12V present intermittently. So pulled out the ETS relay - tested contacts with
ohmmeter & found to be only making contact intermittently when relay lever depressed
- removed relay case by grinding away one corner of the case - cleaned the relay points with fine sandpaper.
replaced the relay case & taped with black insulating tape to keep out dust. Tested relay with ohmmeter & points
now OK. Fault is now cleared & car is operating normally.
Also had previously purchased on Ebay a Can OBD11 scanner for $15 which read the fault codes OK.
Hope this helps other people with similar problem.

Mar 15, 2011 | Hyundai Motor 2003 XG350

1 Answer

I have 2002 xg350 and the water pump went out and then rolled the timing belt off and bent the valves. Pulled the heads and had repaired. reassembled and it ran fine for 24 hrs. and then it popped code...

Hi

The ETS limp home valve may be on. Clean the throttle body and intake runners with intake cleaner with engine running. Then do a ETS initialization as follows:

ETS INITIALIZATION PRCEDURE:
Turn the ignition key to the ON position (for less than one second) and quickly turn the ignition key back to the OFF position.
Wait 10 seconds in off position.The ETS Module performs the INITIALIZATION process and at completion you will hear a click from under dash. Turn the key on for 1 second then start the vehicle.

Hope this helps - Steve

Feb 20, 2010 | Hyundai XG350 Cars & Trucks

1 Answer

I have 8000 miles on my Tucson check engine light came on at start up this morning...gas cap is tight...no problems?????

there are over 200 reasons for the check engine light to come on, the gas tank cap is just one of them, this light and the problem that turned it on are most likely covered under the federal emission warranty, contact the dealer. see trouble code list below for some of the probelems that cause a check enghine light.
P1100 Map Sensor - Malfunction
P1101 Map Sensor - Abnormal
P1102 Map Sensor - Low Input
P1103 Map Sensor - High Input
P1104 Air Flow
P1105 Air Flow - Abnormal
P1106 Air Flow - Low Input
P1107 Air Flow - High Input
P1108 Fuel Pump
P1109 Fuel Pump - Abnormal
P1110 Fuel Pump - Stuck On
P1110 ETS System - Malfunction
P1111 Fuel Pump - Electrical
P1112 Manifold Differential Pressure Sensor
P1112 VGT Actuator - Malfunction
P1113 Manifold Differential Pressure Sensor - Abnormal
P1114 Manifold Differential Pressure Sensor - Low
P1115 Coolant Temperature Input - Abnormal
P1116 Boost Pressure Sensor - Malfunction
P1118 ETS Motor - Malfunction
P1119 Inlet Metering Valve Control
P1120 Electric Governor - Malfunction
P1120 Inlet Metering Valve Malfunction
P1121 APS PWM Output Circuit Malfunction
P1121 Throttle Position Input - Abnormal
P1122 Boost Pressure Control Valve
P1123 Fuel System Rich - Idle
P1123 Timer Position Sensor - Malfunction
P1124 Fuel System Lean - Idle
P1125 Fuel Press Sensor1
P1126 Fuel Press Sensor2
P1127 Fuel System Rich - Part Load
P1127 Control Sleeve Position Sensor
P1128 Fuel System Lean - Part Load
P1130 Start Solenoid- Malfunction
P1131 Injection Quantity Adjust
P1134 O2s Transition Time(B1/S1)
P1135 Injection Timing Servo
P1140 Inlet Air Temperature Sensor Malfunction
P1141 Slow Duty Solenoid- Malfunction
P1145 Main Duty Solenoid- Malfunction
P1146 Idle Co Potentiometer
P1147 Accelerator Position Sensor (ETS) Circuit
P1150 Barometric Pressure Sensor Malfunction
P1151 Accelerator Position Sensor (EMS) Circuit
P1152 Accelerator Position Circuit-Low Input
P1153 Accelerator Position Circuit-High Input
P1154 O2s Transition Time(B2/S1)
P1155 Limp Home Valve- Malfunction
P1159 Variable Induction System
P1162 High Pressure Pump & Fuel Line
P1166 O2s (B1) Control Adaptation
P1166 Limit O2s Lambda Control (B1)
P1167 O2s (B2) Control Adaptation
P1167 Limit O2s Lambda Control (B2)
P1168 O2s (B1/S2) Heater Power
P1169 O2s (B2/S2) Heater Power
P1170 ECM (Barometric Pressure Sensor)
P1171 ETS Valve Stuck - Open
P1172 ETS Improper Motor Current
P1173 ETS Target Following Malfunction
P1174 ETS Valve Stuck - Close #1
P1175 ETS Valve Stuck - Close #2
P1176 ETS Motor Open/Short #1
P1177 ETS Motor Open/Short #2
P1178 ETS Motor Power - Open
P1179 ETS Position F/B-Mismatch
P1180 O2 S1 Heater Circuit- Malfunction
P1180 Fuel Pressure Regulator - Malfunction
P1181 Fuel Pressure Monitoring
P1182 O2 S2 Heater Circuit - Malfunction
P1182 Fuel Pressure Regulator - Short
P1183 Fuel Pressure Regulator - Open
P1184 O2s No Activity (B1/S2)
P1184 Fuel Pressure Regulator - Power
P1185 Fuel Position - Excessive
P1186 Fuel Pressure - Too Low
P1187 Regulator Valve - Stuck
P1188 Fuel Pressure - Leakage
P1189 Governor Deviation
P1190 Intake Throttle Actuator
P1191 ETS Limp Home Valve On
P1192 Limp home - Target Follow Malfunction
P1193 ETS Limp Home - Low Rpm
P1194 Limp Home - TPS2 Position Malfunction
P1195 Limp Home - Target Follow Delay
P1196 ETS Limp Home - Close Stuck
P1300 Spark Timing Adjust Signal
P1300 Injector Specific Data Fault
P1300 Synchronization Error-CKP/CMP
P1301 TDC Sensor - Abnormal
P1302 TDC Sensor - Low Input
P1303 TDC Sensor - High Input
P1304 Phase Sensor
P1305 Phase Sensor - Abnormal
P1306 Phase Sensor - Low Input
P1307 Phase Sensor - High Input
P1307 Accelerator Sensor - Range/Performance
P1308 Ignition Coil.1
P1308 Accelerator Sensor - Low
P1308 Accelerator Sensor Circuit - Low
P1309 Ignition Coil.1 - Abnormal
P1309 Accelerator Sensor - High
P1309 Accelerator Sensor Circuit - High
P1310 Ignition Coil.1 - Low Output
P1310 Injection Control Circuit Fault
P1311 Ignition Coil.1 - High Output
P1312 Ignition Coil.2
P1313 Ignition Coil.2 - Abnormal
P1314 Ignition Coil.2 - Low Output
P1315 Ignition Coil.2 - High Output
P1316 Ignition Coil.3
P1317 Ignition Coil.3 - Abnormal
P1318 Ignition Coil.3 - Low Output
P1319 Ignition Coil.3 - High Output
P1320 Ignition Coil.4
P1321 Ignition Coil.4 - Abnormal
P1321 Glow Indicator Lamp - Short
P1322 Ignition Coil.4 - Low Output
P1322 Glow Indicator Lamp - Open
P1323 Ignition Coil.4 - High Output
P1324 Glow Relay - Malfunction
P1325 Glow Relay - Abnormal
P1325 Glow Relay
P1326 Glow Relay - Stuck On
P1326 Glow Relay - Short
P1327 Glow Relay - Electrical
P1327 Glow Relay - Open
P1330 Spark Timing Adjust Signal
P1331 #1 MF Signal Line Short
P1332 #2 MF Signal Line Short
P1333 #3 MF Signal Line Short
P1334 #4 MF Signal Line Short
P1335 #5 MF Signal Line Short
P1336 #6 MF Signal Line Short
P1337 #7 MF Signal Line Short
P1338 #8 MF Signal Line Short
P1340 IFS 2 Open

Jun 16, 2009 | 2006 Hyundai Tucson

2 Answers

Diagnostic Trouble codes...Hyundai xg300

P1191 ETS Limp Home Valve On P1193 ETS Limp Home - Low Rpm
P1607 Vacuum Sol. Valve Stuck On or Vacuum Solenoid. Valve Stuck On,
I believe you have aproblem in the electronic throttle control motor/actuator, all three code's are related.

Mar 17, 2009 | 2001 Hyundai XG300