Question about 2003 GMC Envoy
The headlights on the envoy are the easiest parts of the car to repair. You just pull the two tabs at the top of the headlights, screw out the bulb containers and you are good to go
Posted on Nov 15, 2008
The battery is on the right side behind the fuse box. You need a metric set to undo the 3 screws. Theres one that attaches to the body, one to the bar that goes along the top, and theres one on the left side below the vacuum hose and air induction. After you've taken out those three, you should lift the whole thing out(battery and shroud) together. It's hard to take the shroud off before you lift the battery out. After that, you have to pry the shoud off the battery. The two terminals in the back make it hard. Then just go to any auto parts store and they'll give you a new one.
Posted on Jan 28, 2009
sounds like a fuse look under the dash panel for fuse cover look at the back of cover and check that fuseThanks for using fix ya Please rate my response thank you very much
Posted on Jan 31, 2009
don't need any special tools, standard sockets sets, "C" clams is a must unless your a He-Man and wrench set, plyer or needle nose will do. I assumed being 2003 your rotor never have been turn and i recommend every time you change your bakes is good idea to have your rotor turn. reason is it will make your pad last lot longer, removed any vibration and better even wear on the pad and eliminate any squealing although is not necessary to do so. make sure you get extra break fluid to bleed the brakes. get your self 5 feet long smallest vacum rubber hoses and a glass jar to bleed your brake fluid in. the rubber vacum hose you going to use to fit on to the bleeding nipple and run the other end of line to your the glass jar to save the brake fluid when you bleed the brakes. when removing caliper, check inspect make sure the rubber seals around your piston look good and not crack or deteriorated. before applying new pad make sure you open the bleed valve to reduce the pressure by turning the bleed nipple counter clockwise and leave it open attach that rubber hoses to the nipple because you going to press on the piston back into it housing with the "C" clamp in order for new pad to fit. becareful not to damage the rubber seals around the piston. its going to take lots of effort to push that piston back in so be a bare with it if needs to. once the pad is back in make sure you keep the reservoir full with brake fluid and then bleed the brake. two people is a good idea to do brake. one will do the pumping the brake and holding it down and other will bleed the nipple. I bleed it 2-3 time will do the job. good luck!
Posted on Jul 17, 2009
Just behind right rear tire up in the wheel well. Air inlet is inside right rear quarter near the accessory inflator. Compressor runs 3 lines one for the accessory inflator and one for each air bag.
THere are also 2 sensors, one on each trailing arm that senses load and then raises and lowers accordingly.
Posted on Feb 17, 2010
Tips for a great answer:
Dec 16, 2014 | 2003 GMC Envoy
Sep 11, 2014 | 2003 GMC Envoy
Jun 05, 2012 | 2003 GMC Envoy
Aug 05, 2011 | 2003 GMC Envoy
Jul 19, 2011 | 2003 GMC Envoy
There are two fuse boxes/block
One fuse block is located under the hood in the engine
compartment on the driver's side of the vehicle.
Remove the primary cover by pressing the two locking
tabs. Remove the secondary cover by snapping off
while lifting. To reinstall the fuse panel cover, reverse
The 2nd fuse box is located under the rear seat cushion
Oct 06, 2010 | 2003 GMC Envoy
Apr 14, 2010 | 2003 GMC Envoy
May 04, 2009 | GMC Envoy XL Cars & Trucks
Jan 14, 2009 | 2002 GMC Envoy
Feb 19, 2017 | 2003 GMC Envoy
275 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: