Question about Cars & Trucks

1 Answer

What causes a P0497 code evap emissions system low purge flow after replacing a purge valve?

Posted by Ian Piparo on

Ad

1 Answer

Rick M

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 4,049 Answers

Bad vent valve, clogged canister, plugged vent hose

Posted on Jul 10, 2017

Ad

5 Related Answers

Anonymous

  • 1665 Answers

SOURCE: im getting a P0441 EVAP

P0441 : Evap. Emission System Incorrect Purge Flow

General Description
The evaporative emission control system prevents hydrocarbon (HC) vapors from the fuel tank from escaping into the atmosphere where they could form photochemical smog. Gasoline vapors are collected in the charcoal canister. The ECM controls the Purge Control Solenoid Valve (PCSV) to purge any collected vapors from the canister back to the engine for combustlon. This valve is actuated by the purge control signal from the PCM and controls fuel vapor from the canister to the intake manifold.
Possible Cause : ● Leakage on hose to PCSV ● Defective PCSV

Posted on Aug 10, 2008

Ad

Anonymous

  • 43 Answers

SOURCE: 2003 Mazda MPV trouble codes

check the pcv hose at the back of the intake manifold it often leaks and will cause several idle problems

Posted on Sep 29, 2008

Anonymous

  • 410 Answers

SOURCE: im getting a P0441 EVAP emission control system

Here is what I could find for your code error as potential causes:
After market parts and accessories nonconforming to the EVAP system specifications.
Damaged, missing or improperly installed fuel filler cap.
Blockage in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube) in EVAP system.
Disconnected or cracked fuel vapor hoses/tubes in EVAP system.
EVAP canister purge valve stuck closed.
Canister vent (CV) solenoid stuck open.
Fuel tank pressure (FTP) sensor malfunction.
EVAP canister leaking.
Fuel vapor control valve tube assembly blocked.
Fuel vapor vent valve assembly blocked.

Obviously the gas cap would be the easiest and cheapest thing to fix.  Just make sure it is put on correctly and tight.  If it is not that, I would have to suggest to take it to a mechanic because the other problems on that list are not really DIY material.  Hopefully it is the gas cap and you can take care of it yourself.  Good luck.

Posted on May 17, 2009

Anonymous

  • 1 Answer

SOURCE: Check Engine light - Code P0441 (Evap Emission

There is an evap purge valve located in the back of the driver side of the engine. This valve needs to be replaced. Had the same code a couple weeks ago. Replaced that valve and the problem was fixed. Hope this helps.

Posted on Dec 29, 2010

Kevin Thorpe

  • 400 Answers

SOURCE: I got a Error Code

P1442 usually gas cap. P1449 usually vent solenoid. P1441 usually always a faulty FTP sensor. Very problematic to Malibu, Grand Am Cavaliers and Aleros. That would be my first area to check. They are also known for poor wiring connections at the Left rear passthru connector to the fuel tank and vent solenoid, but not necessarily for that code.

Posted on Jan 25, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does fault code P0497 mean for Honda Cr-v ?


code p 0497 refers to evaporative emission system ---low purge flow====causes ---wiring---EVAP valve ---hoses blocked ---mechanical fault

Dec 30, 2015 | Honda Cars & Trucks

1 Answer

Hello there,my 2001 echo is lighting up trouble codes p0440 p0441 p0446; how and where should i start?


code p0440 refers to evaporative emission (EVAP) system--malfunction=== causes --hose connections --intake leak--EVAP canister purge valve
code po441 refers to EVAP --incorrect flow detected==causes the same as for po440
code po446 refers to EVAP system vent control --circuit malfunction===causes --wiring---EVAP can purge valve--ECM
generally I would replace the purge valve as it is common to all codes

Feb 03, 2014 | Cars & Trucks

1 Answer

Emissions Code


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Purge control VSV connector disconnected.
- Evaporative Emission (EVAP) Canister Purge Regulator Valve is faulty/jammed.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
- Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve.
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Jan 10, 2014 | Toyota Cars & Trucks

1 Answer

What is scan code p0497


Evaporative emission purge flow low. Causes: wiring, EVAP valve, hoses blocked or mechanical fault.

Apr 16, 2013 | Cars & Trucks

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

2 Answers

I have a 07 impala with the 3.5 motor and i am getting three diffetent codes. P0411, p0449 and p0455. I disconnected the battery and the engine lite went off for one day and its back on again. The car is...


Your best bet take it to a qualified repair shop . It takes special tool's to diagnose evaporative emission system's .
DTC P0411 : Secondary Air Injection (AIR) System Incorrect Air Flow Detected
DTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit
DTC P0455: Evaporative Emission (EVAP) System Large Leak

Nov 23, 2017 | Chevrolet Impala Cars & Trucks

2 Answers

My 1995 subaru legacy lsi cuts out when I rev the engine around 1 rpm. Plus the check engine light is on. I took it to the dealership and they couldn't fix it, but they got a code from the check engine...


code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

May 21, 2017 | 1995 Subaru Legacy

2 Answers

Check engine lite came on code is p1443 what does this code mean


P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

May 04, 2011 | 1997 Ford Escort

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

2 Answers

P0441 EVAP Control System Incorrect Purge Flow


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

Jun 15, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

522 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23438 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...