Question about Ford F-250

1 Answer

Wiper control module location on a 2000 f250

The part module I bought has a 14 pin connector. I replaced the motor and the switch, neither fixed the problem

Posted by Gary Simpson on

Ad

1 Answer

Jeff Armer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 15,575 Answers

Did you check the wiper relay's in the under hood fuse box ? There are two ,wiper run/park relay & wiper high low relay ! Also ,did you check fuse's ? fuse # 11 - 30amp location cental juction box . The wiper switch is a input to the GEM module . Generic electronic module . The module in most cases isn't the problem ! Learning how to test these electronic systems is , people do not know how to test so they just replace parts . What they should do is take the vehicle to ford certified Technician who has the knowledge and testing equipment to find an fix it .

The generic electronic module (GEM) receives inputs from the following:

  • multifunction switch
  • anti-lock brake control module (vehicle speed signal [VSS])
  • ignition switch
The GEM uses these inputs to control the outputs to the following:
  • windshield wiper high/low relay
  • windshield wiper run/park relay
  • windshield washer relay
  • rear wiper motor relay
  • rear window washer relay

  • GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1240 Wiper Washer Rear Pump Relay Circuit Failure GEM GO to Pinpoint Test K . B1241 Wiper Washer Rear Pump Relay Circuit Short to Battery + GEM GO to Pinpoint Test K . B1342 ECU is Defective GEM CLEAR the DTCs. REPEAT the GEM self-test. If DTC B1342 is retrieved, INSTALL a new GEM. REFER to Section 419-10 . B1431 Wiper Brake/Run Relay Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers stay on continuously, GO to Pinpoint Test C . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM GO to Pinpoint Test B . B1434 Wiper Hi/Low Speed Relay Coil Circuit Failure GEM GO to Pinpoint Test D . B1436 Wiper Hi/Low Speed Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test D . B1438 Wiper Mode Select Switch Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If both the windshield and rear window wipers are inoperative, GO to Pinpoint Test L . B1441 Wiper Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test C . B1446 Wiper Park Sense Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the speed dependent interval mode does not operate correctly, GO to Pinpoint Test G .
    If both windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1450 Wiper Wash/Delay Switch Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F .
    If both the windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM If the windshield wipers stay on continuously, GO to Pinpoint Test C .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F . B1458 Wiper Washer Pump Motor Relay Circuit Failure GEM GO to Pinpoint Test F . B1460 Wiper Washer Pump Motor Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test F . B1473 Wiper Low Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E . B1475 Accessory Delay Relay Contact Short to Battery GEM REFER to Section 501-11 . B1476 Wiper High Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper does not operate correctly, GO to Pinpoint Test E . B1611 Rear Wiper Mode Switch Circuit Failure GEM GO to Pinpoint Test H . B1614 Rear Wiper Mode Switch Circuit Short to Ground GEM GO to Pinpoint Test I . B1820 Rear Wiper Motor Up Relay Circuit Short to Battery + GEM GO to Pinpoint Test H . B1839 Rear Wiper Motor Circuit Failure GEM GO to Pinpoint Test H . - All other DTCs. GEM REFER to Section 419-10

Posted on Aug 02, 2017

  • Jeff Armer Aug 02, 2017

    The windshield wipers are inoperative
    Windshield wiper run/park relay.
    Windshield wiper high/low relay.
    multifunction switch.
    Circuitry.
    Ignition switch.
    Windshield wiper motor.
    Generic electronic module (GEM).
    GO to Pinpoint Test B .

×

Ad

5 Related Answers

Anonymous

  • 113 Answers

SOURCE: BMW 740IL Wiper Issue

try checking for a short to power on ur 12 volt comming into motor also check for a good ground at the plug for ur wiper motor

Posted on Jun 17, 2008

Ad

Anonymous

  • 85 Answers

SOURCE: Location of the blower motor control module

The module is located in the ducting for the heater and is accessed from the passenger area of the front seat. I think it is just under the dash but you may have to remove the glove box. it is a rectangular item held in with four screws. and should have two connectors going to it. You have to be sure to get the right replacement if you r replacing it.
thanks.

Posted on Feb 26, 2009

honeymokey

honeymokey

  • 3113 Answers

SOURCE: location of blower motor control module

Its just above the blower motor on passenger side on housing. Goes in from the top side hidden, by cover on firewall.

Posted on May 17, 2009

Anonymous

  • 169 Answers

SOURCE: replaced wiper motor but still won't work buzzes

can you move the linkage when you pulled the motor?

Posted on Aug 30, 2009

c17hydro

Greg Bernett

  • 2989 Answers

SOURCE: Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?

Removal & Installation To Remove:

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Posted on Oct 01, 2009

Testimonial: "Fast and accurate response."

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 crown vic. p71v 1st the fluid stopped and the wipers would'nt shut off, now 1 day later no fluid still and the wipers stop working completely, please help me


Principles of Operation
The windshield wiper motor receive inputs from the following:
  • multifunction switch
  • lighting control module (LCM)
  • ignition switch
  • battery junction box (BJB)
  • central junction box (CJB)
The following components are integrated into the windshield wiper motor:
  • windshield wiper motor module
  • high/low speed relay
  • run/park sensor (Hall effect)
  • washer pump relay
High Speed Windshield Wipers
High speed is activated when the multifunction switch supplies ground to the windshield wiper motor module inputs. The windshield wiper motor module then supplies ground to the run/park sensor and high/low relay coil, activating the relay with voltage supplied from the ignition switch (RUN/ACC) through the central junction box (CJB). When the windshield wiper motor module receives voltage from the run/park sensor, it removes ground from the run/park sensor, deactivating it. The windshield wiper motor continues to operate from voltage connected through the run/park sensor until the Hall effect senses the magnet in the motor. When the Hall effect senses the magnet in motor the windshield wiper motor returns to the park position, the internal run/park sensor grounds the windshield wiper motor module input and the windshield wiper motor module removes ground from the windshield wiper high/low relay coil, deactivating the high/low relay and windshield wiper motor. The windshield wiper motor module continues to cycle the windshield wipers until the inputs from the multifunction switch are changed from the high speed position.
Low Speed Windshield Wipers
Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The windshield wiper motor module then supplies ground to only the windshield wiper run/park relay coil, activating it. When the windshield wiper run/park relay is activated, the deactivated windshield high/low relay connects voltage to the windshield wiper motor low input activating the wiper motor. The windshield wiper motor module continues to operate the windshield wiper motor in the same manner as in high speed, but in low speed with the wiper motor connected to the low speed input.
Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper run/park relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated, supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect sensors senses the wiper motors magnet, which turns off the run/park sensor output to the windshield wiper run/park software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.
Washer System
The windshield washer is activated by the internal wiper motor module when it receives a ground from the multifunction switch between the washer input. Dependent on the correct ground, the internal wiper motor modules activates the windshield washer relay (internal) by grounding the respective relay coil. When the relay is activated, it connects voltage to the washer pump while the washer level switch provides ground to the washer pump.
Default Mode
The windshield wiper motor defaults to this mode when the run/park sensor does not sense the hall effect magnet inside wiper motor. This can be caused by obstruction of the windshield wipers or a binding linkage. The windshield wiper motor will continue to operate in a high/low speed condition for a period of 60 seconds.

Symptom Chart
Symptom Chart Condition Possible Sources Action
  • The wipers are inoperative
  • Multifunction switch
  • Circuitry
  • Ignition switch
  • Windshield wiper motor
  • Go To Pinpoint Test A .

Do you know how to test automotive electrical circuits using a factory diagnostic test procedure flow chart ?

PINPOINT TEST A: THE WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 2025 (RD/YE) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 2025 (RD/YE), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 65 (DG), harness side and ground.
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 676 (PK/OG) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 676 (PK/OG), harness side and ground.
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202b.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR AN OPEN
  • Measure the resistance between C202b pin 5, circuit 57 (BK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202b harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202b Windshield Wiper Motor C125 pin 6, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 1, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 4, circuit 63 (RD) pin 9, circuit 63 (RD)
  • Are the resistances less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as outlined in this section.
  • Does the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. The concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

Apr 30, 2018 | Ford Crown Victoria Cars & Trucks

1 Answer

Wipers in up position in off. 94 lincoln town car. How do the wipers return to rest position?


Do you know how to do electrical testing ?
PINPOINT TEST E: WINDSHIELD WIPERS WILL NOT PARK AT PROPER POSITION E1 CHECK WIPER MOTOR GROUND
  • Disconnect connector from windshield wiper motor.
  • Check continuity to ground at Circuit 57 (BK).
Is ground OK? Yes No GO to E2 . SERVICE open in Circuit 57 (BK). RESTORE vehicle. RETEST system. E2 CHECK FOR POWER AT WIPER MOTOR
  • Place ignition switch at RUN and multi-function switch at OFF.
  • Check for battery voltage between Pin 1, Circuit 65 (DG) and Pin 4, Circuit 57 (BK) at the windshield wiper motor connector.
Is B+ present? Yes No GO to E3 . SERVICE open circuits. RESTORE vehicle. RETEST system. E3 CHECK MOTOR CIRCUIT CONTINUITY THROUGH WINDSHIELD WIPER CONTROL MODULE
  • With multi-function switch at OFF, check continuity between Circuit 28 (BK/PK) and 56 (DB/O) and between Circuits 61 (Y/R) and 63 (R).
Is continuity OK? Yes No GO to E5 . GO to E4 . E4 CHECK CIRCUITS TO WIPER CONTROL MODULE
  • Disconnect wiper control module connector.
  • Check continuity of Circuits according to the chart below from the wiper motor to the wiper control module.

    Wiper Control Module Connector Wiper Motor Connector Pin Circuit Pin 6 Pin 2 28 (BK/PK) Pin 8 Pin 6 56 (DB/O) Pin 12 Pin 5 61 (Y/R) Pin 13 Pin 3 63 (R)
Is continuity present? Yes No REPLACE wiper control module. RESTORE vehicle. RETEST system. SERVICE open circuits. RESTORE vehicle. RETEST system. E5 CHECK WIPER MOUNTING ARM/PIVOT SHAFT
  • Check that windshield wiper mounting arm and pivot shaft and linkage is not bent, cracked or mis-positioned.
Is windshield wiper mounting arm and pivot shaft linkage OK? Yes No REPLACE windshield wiper motor. RESTORE vehicle. RETEST system.

Nov 14, 2016 | 1994 Lincoln Town Car

1 Answer

Y need book for fuse box


Fuses are listed here
* = maxi fuse
1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay
6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay
mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator
Interior fuse panel (mini fuses)
1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**
15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat,

i copied this off another post hope this helps

Oct 09, 2016 | 2003 Ford Explorer

1 Answer

My running lights are working just fine no brake lights any suggestions? 1999 Lincoln continental


Brake light switch ? Lighting control module , fuse's ?
The stoplight switch is protected by Fuse 32 (15A). This fuse is hot at all times. With the stoplight switch closed, power is provided to the stoplamps through the lighting control module through Circuits 9 (LG/O) and 5 (O/LB). Ground is provided to the stoplamps through Circuit 57 (BK).
Symptom Chart-Stoplamps
Refer to the Electrical and Vacuum Troubleshooting Manual for connector numbers cited in the pinpoint tests. Use Rotunda 88 Digital Multimeter 105-R0053 or equivalent to perform pinpoint tests.
Symptom Chart-Stoplamps Condition Possible Source Action
  • No Communication With Lighting Control Module
  • Circuitry.
  • Lighting control module.
  • GO to Pinpoint Test BA .
  • Stoplamps Inoperative
  • Open fuse.
  • Circuitry.
  • Lighting control module.
  • GO to Pinpoint Test
You may want to take to a repair shop !

PINPOINT TEST BB: STOPLAMPS INOPERATIVE BB1 TEST STOPLAMPS
  • Press stoplight switch.
  • Check stoplamps and rear high mount lamp.
Are lamps on? Yes No RELEASE switch and make sure that lamps turn off. CHECK Fuse 32 (15A). REPLACE open fuse if open, RESTORE vehicle, RETEST. If fuse is good, GO to BB2 . BB2 TEST STOPLIGHT SWITCH INPUT
  • Connect Rotunda New Generation Star (NGS) Tester 007-00500 or equivalent to data link connector.
  • Enter diagnostic data link.
  • Enter lighting control module.
  • Enter PID/data monitor and record.
  • Select PID: BOO_LCM - Stoplight Switch Status.
  • Hold stoplight switch.
Does data display read ON? Yes No GO to BB5 . GO to BB3 . This is with a factory scan tool , a code reader will not work !
BB3 TEST FOR VOLTAGE AT STOPLIGHT SWITCH
  • Test for voltage at input Circuit 10 (LG/R) to stoplight switch connector C253 .
Is B+ present? Yes No GO to BB4 . SERVICE Circuit 10 (LG/R) feeding stoplight switch. RETEST system. BB4 TEST VOLTAGE OUTPUT AT STOPLIGHT SWITCH
  • Test for voltage at output Circuit 511 (LG) of switch connector C253 .
  • Press stoplight switch.
Is voltage B+ at the switch? Yes No SERVICE Circuit 511 (LG). RETEST system. REPLACE stoplight switch. RETEST system. BB5 TEST POWER TO LIGHTING CONTROL MODULE
  • Disconnect connector C207 from lighting control module.
  • Test for voltage at connector Pin C207 , Circuit 907 (Y/W) and Pin C207 , Circuit 906 (R/O).
Is voltage B+? Yes No GO to BB6 . SERVICE Circuits 906 (R/O) and/or 907 (Y/W). RETEST system. BB6 TEST OUTPUTS
  • Using jumper wires, short Pin C207 , Circuit 907 (Y/W) to Pin C207 , Circuit 9 (LG/O). Using jumper wires, short Pin C207 , Circuit 906 (R/O) to Pin C207 , Circuit 5 (O/LB).
Do stoplamps illuminate? Yes No REPLACE lighting control module. RETEST system. SERVICE Circuits 5 (O/LB) and 9 (LG/O) for open circuit or damaged bulbs. REPLACE open bulbs as necessary. RESTORE vehicle, RETEST. This is Lincoln factory service info !

Jul 04, 2015 | Lincoln Cars & Trucks

1 Answer

Fuse for the alarm system


Here is the full list of fuses for you! and for the car.

Fuses on E-box, on left in Engine Compartment

Fuse 1 - Not assigned

Fuse 2 - 10/15A - Engine control unit

Fuse 3 - 5A - Radiator fan control unit

Fuse 4 - 5/10/15A - Lambda probe heater,
Lambda probe 1 heater after
catalytic converter

Fuse 5 - 10A, 20A - Lambda probe heater1,
Lambda probe 1 heater after
catalytic converter,
Fuel system diagnostic pump,
Charge pressure control solenoid
valve,
Exhaust gas recirculation cooler
change-over valve,
Crankcase breather heater element,
Vacuum pump for brakes

Fuse 6 - 5A, 10A,15A - Fuel system diagnostic pump,
Throttle valve module,
Activated charcoal filter system
solenoid valve 1,
Continued coolant circulation pump,
Auxiliary air heater heating element

Fuse 7 - 20A, 5A - Ignition transformer,
Fuel pressure regulating valve,
Fuel metering valve

Fuse 8 - 10A - Throttle valve module,
Activated charcoal filter system
solenoid valve 1

Fuse 9 - 5A - Automatic glow period control unit,
Electric fuel pump 2 relay,
Fuel pump relay

Fuse 10 - 5A - Speedometer sender,
Brake light switch

Fuse 11 - Not assigned

Fuse 12 - 5A - Coolant circulation pump

Fuse 13 - 5A - Water pump

Fuse 14 - 5A - Engine control unit

Fuse 15 - 30A - Voltage stabiliser

Fuse 16 - 30A - ABS control unit

Fuse 17 - 30A - Automatic gearbox control unit

Fuse 18 - 20A - Automatic gearbox control unit

Fuse 19 - 1A - Onboard supply control unit

Fuse 20 - 30A - Onboard supply control unit (AW0)
Automatic intermittent wash and
wipe relay (AW1)

Fuse 21 - 50A - Secondary air pump motor

Fuse 22 - Not assigned

Fuse 23 - 40A - ABS control unit

Fuse 24 - 50A - Trailer detector control unit

Fuse 25 - 50A - Terminal 15 voltage supply relay 2

Fuse 26 - 60A - Automatic glow period control unit

Fuse 27 - 60A - Radiator fan

Fuse 28 - 40A - Onboard supply control unit (AW1)

Fuse 29 - 40A - Onboard supply control unit (AW1)

Fuse 30 - 50A - Terminal 75 voltage supply relay 1

Fuse 31 - 30A - Amplifier

Fuse 32 - Not assigned

**************************************************

Fuse assignment - Interior Fuse Panel

Fuse 1 - Not used

Fuse 2 - 5A - Electronic steering column lock control module

Fuse 3 - 10A - Instrument cluster control module

Fuse 4 - Not used

Fuse 5 - Not used

Fuse 6 - 10A - Vehicle electrical system control module,
Interior ceiling lights,
Tail lights

Fuse 7 - 5A - Fog lamp relay,
Instrument panel and switch illumination dimmer switch,
License plate lamps,
Vehicle electrical system control module

Fuse 8 - 7.5A - Windshield and headlamp washer pump switch,
Windshield washer pump

Fuse 9 - 5A - Airbag control module

Fuse 10 - 10A - Right steering column switch

Fuse 11 - Not used

Fuse 12 - Not used

Fuse 13 - 5A - Automatic dimming interior rearview mirror,
Light recognition sensor,
Parking aid control module,
Air quality sensor,
High pressure sensor,
Climatronic control unit,
Tire pressure monitoring button,
Back-up lamp switch,
Left washer nozzle heater,
Right washer nozzle heater,
28-pin connector

Fuse 14 4- 10A - Left steering column switch,
ABS control module,
Light switch,
Airbag spiral spring/return spring with slip ring,
Fuel pump control module,
Data bus on board diagnostic interface

Fuse 15 - 10A - 16-pin connector (diagnostic connector),
Instrument panel and switch illumination dimmer switch,
Headlamp range control adjuster,
Auxiliary heater operation relay,
Mass airflow sensor,
Positive crankcase ventilation heating element,
Left front headlamp,
Left headlamp beam adjustment motor,
Right front headlamp,
Right headlamp beam adjustment motor,

Fuse 16 - 10A - Engine control module

Fuse 17 - Not used

Fuse 18 - 15A - Left front headlamp

Fuse 19 - 15A - Right front headlamp

Fuse 20 - 10A - Automatic transmission control module,
Selector lever sensor system control module,
Tiptronic switch,
Climatronic control unit,
Ignition/starter switch

Fuse 21 - Not used

Fuse 22 - 10A - Ignition/starter switch,
Converter box,
Alarm horn,
Interior monitoring sensor,
Alarm horn relay,
Dual tone horn relay

Fuse 23 - 10A - Vehicle electrical system control module,
16-pin connector (diagnostic connector),
Light switch,
Rain/light recognition sensor,
Compass magnetic field sensor,

Fuse 24 - 10A - Vehicle electrical system control module,
Access/start authorization control module

Fuse 25 - 15A - Automatic transmission control module,
Selector lever sensor system control module,
Multifunction transmission range switch

Fuse 26 - 15A - Brake system vacuum pump

Fuse 27 - Not used

Fuse 28 - 40A - Auxiliary heater operation relay

Fuse 29 - 1A - Vehicle electrical system control module,

Fuse 30 - 20A - Cigarette lighter,
12 V socket,
12 V socket 2,
Blocking diode

Fuse 31 - 30A - Light switch

Fuse 32 - 20A - Light switch

Fuse 33 - 40A - Heater/heat output switch,
Fresh air blower relay,
A/C control module,
Fresh air blower switch

Fuse 34 - 15A - Left front headlamp,
Left front headlamp,
Instrument cluster control module

Fuse 35 - 10A - Steering column electronics control module,
Instrument cluster control module,
Signal horn activation,
Data bus on board diagnostic interface

Fuse 36 - 25A - Vehicle electrical system control module

Fuse 37 - 15A - Left front headlamp DRL

Fuse 38 - 15A - Right front headlamp DRL

Fuse 39 - 15A - Low beam relay

Fuse 40 - 15A - Towing recognition control module

Fuse 41 - 15A - Towing recognition control module

Fuse 42 - 20A - Towing recognition control module

Fuse 43 - 30A - Front passenger door control module

Fuse 44 - A25 - Rear window defogger relay,
Vehicle electrical system control module

Fuse 45 - 30A - Driver door control module,
Front passenger door control module

Fuse 46 - 30A - Left rear door control module,
Right rear door control module

Fuse 47 - 15A - Fuel pump control module,
Fuel pump relay,
Fuel primer relay

Fuse 48 - 20A - Vehicle electrical system control module,
Vehicle electrical system control module,
Vehicle electrical system control module,

Fuse 49 - 20A - Climatronic control unit,
A/C control module

Fuse 50 - 30A - Front seat heating control module

Fuse 51 - 30A - Power sunroof control module

Fuse 52 - 20A - Dual tone horn relay

Fuse 53 - 15A - Front seat heating control module

Fuse 54 - 15A - Fog lamp relay

Fuse 55 - 20A - Light switch,
Left steering column switch

Fuse 56 - Not used

Fuse 57 - 15A - Radio,
Radio/navigation display unit control module

Fuse 58 - 1A, 30A - Telephone transceiver
DC/AC converter with socket, 12V-230V

Fuse 59 - 30A - Amplifier

Fuse 60 - 30A - Auxiliary heater control module


Hope this helps

--N

May 31, 2014 | 2010 Volkswagen Jetta

1 Answer

97 buick century has no data from OBD2 scanner.


The protocol is class 2 . Maybe your code reader is no good .
012 GM Class II Communications

Data Link Connector (DLC)
The data link connector (DLC) contains the following serial data links:
• Class II
• Entertainment and Comfort (E&C)
The DLC also provides a power source for the scan tool as follows:
• Unswitched voltage (B+) at DLC terminal 16 (circuit 1450)
• Ground at terminal 4 (circuit 1450) and terminal 5 (circuit 1550)

Class II Serial Data Link
The class II serial data link allows the following modules to communicate data with each other:
• Body control module (BCM)
• Electronic brake traction control module (EBTCM)
• Heater-A/C control (if equipped with RPO CJ2)
• Instrument panel cluster (IPC)
• Powertrain control module (PCM)
• Inflatable Restraint Sensing and Diagnostic Module (SDM).
The Class II serial data link allows a Scan Tool scan tool to communicate with the above modules for diagnostic and testing purposes. The Class II serial data link is located at the DLC connector terminal 2. Terminal 2 consists of the following circuits:
• Circuit 1036
• Circuit 1037
• Circuit 1128
• Circuit 1049
• Circuit 1122
• Circuit 1132
Entertainment and Comfort (E&C) Serial Data Link
The entertainment and comfort (E&C) serial data link allows a scan tool to communicate with the radio or the mobile telephone handset the remote CD player (if equipped). This communication is for diagnostic and testing purposes. The E&C serial data link is located at the DLC connector terminal 14, circuit 835.
PIN #9 goes to the air bag module .

Aug 04, 2017 | 1997 Buick Century

1 Answer

Location of cooling fan fuse


The radiator cooling fan on your 1990 Ford Thunderbird Super-Coupe is supplied power via the BLACK, 18 Gauge, fusible link near the battery.
If your cooling fan is not getting any power to operate (and you are certain that the fan motor is in good working order) the most likely cause of you fan not working is a failure in the Constant Control Relay Module (CCRM), which is mounted to the upper radiator support.

I have replaced many of these because the circuit boards inside them like to burn.

HERE IS HOW TO TEST IT:

Check for power at the CCRM on pins 3 and 4 BLACK/ORANGE wires. If there is power there, the fusible link is good. If there is no power at these connectors, repair the fusible link or the circuit between the fusible link and the CCRM.

Then, the Powertrain Control Module (PCM) turns the fan on by grounding the fan relays inside the CCRM at Pins 14 and 17.

So if you have power on the BLACK ORANGE wires, You should be able to manually turn the fan on by grounding Pin 14 (TAN/ORANGE) for fan LOW speed and Pin 17 (GREEN/PURPLE) for fan HIGH speed.

If grounding these wires does not get the power to come on at the fan motor, then the CCRM needs to be replaced.

If this makes the power come on (at the motor connector) but the motor will not run, then you need to replace the fan motor.

If grounding these wires makes the motor run, you have a problem with the engine coolant temperature sensor or the PCM.

Apr 22, 2012 | 1990 Ford Thunderbird

1 Answer

My 2003 grand am's emergency flasher is clicking intermittantly and sporadically without being turned on. have replaced the flasher hazard switch/module, but it didn't fix the problem.


Hello! The Hazard Switch/Module connector has the following wires of interest...Pin G=Dark Blue (right side lights)...Pin F=Light Blue/Black (left side lights)...Pin H= Purple (flasher battery)...And Pin A=Black (ground)...In order for the lights to flash, without pressing the switch, Flasher Battery must be applied to Pins G and/or F...When the problem occurs are all external lights flashing or just one side? Visually inspect the connector for bent pins and the harness for bare or frayed wires...If you have a multimeter and a wee bit of experience using it; Set the ohm meter to X10 scale...Measure from Pin A (black wire) to the center of the negative battery post...Reading should be zero ohms or very close to it...Send results...

Guru.......saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Nov 20, 2010 | 2003 Pontiac Grand Am

1 Answer

Abs fuse


Fuses are listed here

* = maxi fuse

1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay

6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay

mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump2.gif relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator


Interior fuse panel (mini fuses)

1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**

15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat, Message center Attached images fuse%20box001.jpg?imgmax=800 __________________

Oct 29, 2009 | 2003 Ford Explorer

4 Answers

I need a fuse box diagram for a 2003 Ford Explorer Sport


I believe that this is what you are looking for.....
Fuse and relay locations--2nd generation power distribution box Layout- I think this is a good sticky candidate--

attachment.php?attachmentid=29397&d=1133918512

Fuses are listed here

* = maxi fuse

1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay

6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay

mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator


Interior fuse panel (mini fuses)

1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**

15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat, Message center Attached images fuse%20box001.jpg?imgmax=800 __________________

Oct 10, 2009 | 2003 Ford Explorer Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

3,843 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...