Question about 2005 Ford Escape

Open Question

2005escape3.0,just changed wireing harness due to bad wires to all 4 02 sensors. That problem seems to be fixed,but now it pulls 4 trany codes/713/743/750/755. I have owned this thing since October

Posted by Phillip watt on

Ad

5 Related Answers

Anonymous

  • 79 Answers

SOURCE: 1998 Maxima misfire code cylinder #1

your not getting any fuel into the cylinder

Posted on Mar 22, 2009


mecanica03

ROBERT GARCIA

  • 918 Answers

SOURCE: o2 sensor

try to reset by disconnect negative battery terminal few minutes

Posted on Apr 20, 2009

Ad

Louis Richard

  • 9 Answers

SOURCE: need color code for wiring harness for 2001 honda accord!

check out http://www.hondahookup.com/manuals/

Posted on Sep 12, 2009

Ken17402

Ken Long

  • 615 Answers

SOURCE: 2001 mitsubishi galant misfire cyl

check moter and switch wichever is bad replace

Posted on Nov 26, 2010

Tooldude1969

BUBBA JONES

  • 106 Answers

SOURCE: Radiator fan not working on

IASounds like the radiator fan motor is bad (not uncommon for a chrysler product)
You can replace the fan motor (DIY) for around $100 (oreily autoparts) or the the entire fan assembly for around $300 (DYI) .
Replacing the fan motor will take about 2-3 hours.....taking out the fan assembly will consume most of your time.
hoppe this helps.

Posted on Jul 13, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check & fix wiring on abs system.


If bearing/speed sensor assembly has been changed most lokely wiring. Use an ohm meter hooked between the two pins of the wiring harness side plug end. There will be resistance on this plug. Move/bend the wiring while the meter is hooked up and observe the reading. If the reading changes drastically or goes OL then the harness is bad. These harnesses are common problems as they flex as the wheels are turned. The dealership sells them for replacement.

Oct 12, 2015 | 2007 Buick Rendezvous

1 Answer

F 150 Code P1747


This code is a trany solenoid failure code that pertains to the epc circuit. When this circuit fails, the vehicle will go to a limp mode or harsh shifting including hesitation and stalling. To check verify when the code appears after the code is reset... use a DVOM and check the voltages going to the epc (electronic pressure control) soleniod. To locate use a wiring diagram so you can locate the epc wires. Once tested, you can verify if the solenoid is working or getting proper voltage signal from the engine computer.

If you decide to replace the epc sensor, make sure the wirings connected to it is not shorting out due to bad insulation or poor routing. In most cases, a defective shorted wire is enough to make the epc solenoid to fail. Note: during the test, make sure the trany is warmed enough since some of these shorted wires will only come out after the vehicle is running for sometime which will cause intermittent flashing of the code. Finally, you can also check the integrity of the wires by tracing it from the trany upto the right module using a wiring diagram. Any DIY person can do this as long as he has the map (wiring diagram) to do it.

Apr 12, 2013 | Cars & Trucks

1 Answer

Why does my 1997 jeep wrangler backfire and buck? I just replaced the sensors and then the computer


My problem bucking/backfiring after 20min cool down was due to bad O2 exhaust sensor. Also discovered same during certain driving conditions was due to battery sliding into computer wiring harness disrupting sensor input/output signals. Cured problem by placing 1" spacer on rear battery clamp to push battery forward away from computer wiring harness. This cured the problem from ever reoccurring.

Apr 19, 2012 | 1997 Jeep Wrangler

1 Answer

This code keeps coming up we changed the o2 sensor and put new plugs and wires on. The truck is hesitating and seems to lose power going up hills and is now smoking. It is a 2004 chevy avalanche.


This could be due to the wrong O2 sensor, Bad Catalytic Convertor, EGR valve or something along those lines. Did you replace this with an OEM part and not have to change the wiring harness or did you have to change the wirings? The other most common issue is you changed it with a non-OEM product and the O2 sensor is not reading correctly. Check to make sure wires are hooked up correctly. Also not know the details of this vehicle it can be that you changed the wrong O2 sensor also, most vehicles have an O2 sensor before and after the Catalytic Convertor

May 19, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I dropped off my 2004 Hyundai Tiburon for repair due to high fuel consumption. I was informed that all my O2 sensors are not working and I was advised to replace all of them but first try replacing the...


Is check engine lamp on now? If it is not on who is going to pay for all the parts and labor,is gas mileage that bad, because it might take along time to get any payback for the repairs.I under stand you want the car right but some times the cost is to high. Good luck

Dec 09, 2010 | Hyundai Tiburon Cars & Trucks

2 Answers

Check engine light came on then trans started acting up looked under the car and there is a wire hanging under the trans.fluid pan.it looks like this wire came unpluged from the trans.where do i plug this...


You need to have codes pull from your computer, if you don't have a scan tool go to any auto parts or some one like autozone and then will do it for free, once you get that code it will let you know where to start looking at, if your still not sure, get back with us with the code number here at FixYa so we can help you with your trouble code. That harness could also be for some else that your don't used and just there, some time's Ford will used the same harness on a few of there car's.

Jun 29, 2010 | 1992 Ford Taurus

1 Answer

Hard shifting 4l60e


How is the linkage from the steering column to the trany. Did it get lined up after the engine and trany was put in? May just need an adjustment. You can also check the connections at your speed sensors. Make sure wires or harnesses didn't get pinched during assembly.

May 23, 2009 | 1994 Chevrolet C2500

2 Answers

Have a 03 pt cruiser with a trouble code P0302, stubbles bad and smells rich.


The P0302 Code points to a misfire detected on the # 2 cylinder. If its stumbling, I would first suspect the plug or wire is bad. I believe the ignition coil on that vehicle is a single coil pack with four terminals, so if only the P0302 code is coming up I would start with the plug and wire. May be time to do a tune up and just replace all the splugs and spark plug wires.

Dec 28, 2008 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Ford Escape Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...