Where is the camshaft positioning sensor located on a '94 Chevy Camaro Z28,5.7 liter, V8?

Question edited for clarity.
Question moved to model category.

Diagrams in the link

https://www.google.com/search?q=1991+Chevy+Camaro+RS+V8.+I+need+vacuum+line+schematic

..

P0010, P0011 (Intake/Exhaust Camshaft Solenoid) 2013 Chevy Malibu
https://www.youtube.com/watch?v=-RhsWasBAXA
Replacing a Camshaft Position Sensor on a Chevrolet 2.4 Ecotec P0340
https://www.youtube.com/watch?v=uF9l2gtDYIk
GM 2.4 Ecotec Camshaft Position Sensor - How To Test & Replace
https://www.youtube.com/watch?v=dOvwSncdP0g
2011 Chevy Malibu 2.4 camshaft senors location
https://www.youtube.com/watch?v=YCNRrv4r2Uk
2013 Chevy Malibu P0014
https://www.youtube.com/watch?v=VLNnc8v8TVw

It is in the front of the engine just under the harmonic balancer.

2009 JAGUAR XF 4.2L V8 Supercharged Auto Parts

https://www.rockauto.com/.../x,carcode,1442330,d,2009_JAGUAR_XF_...

RockAuto has parts for your 2009 JAGUAR XF 4.2L V8 Supercharged and all ... XF 4.2L V8 Supercharged Ignition Parts, Camshaft Position Sensor Crankshaft ...

Jaguar XF Crank Position Sensor - PartsGeek.com

www.partsgeek.com > ... > Jaguar Crank Position Sensor > XF Parts

Oct 1, 2009 - They are available for the following Jaguar XF years: 2010, 2009, 10, 09. ... 10 2010 Jaguar XF Crank Position Sensor 4.2L V8 Intermotor.
Images for 2009 XF 4.2L crankshaft position sensor ...

This system does not use the ignition module used on the DI systems in the past. The VCM controller now controls the ignition control (IC) and bypass functions.
The crankshaft sensor, located in the front engine cover, is perpendicular to a target wheel attached to the crankshaft. The target wheel is equipped with slots situated 60 degrees apart. As the crankshaft rotates, the target wheel rotates past the crankshaft position sensor. The rising and falling edges created by the slots cause a signal to be sent back to the VCM. This signal occurs three times per crankshaft revolution and is referred to as the 3x signal for V6 applications. The signal occurs four times per crankshaft revolution and is referred to as the 4x signal for V8 applications.
The VCM then utilizes this 3x (V6) or 4x (V8) signal in order to provide the correct spark to the engine by way of the single coil driver module. The single coil driver module is basically an electronic switch that when commanded by the VCM, causes the primary coil voltage to breakdown, energizing the secondary coil and providing a spark via the coil wire to the distributor cap. The distributor consists of the following components:
The system consists of the following components:
?€¢
Vehicle control module (VCM)

?€¢
Distributor

?€¢
Ignition coil driver module

?€¢
Ignition coil

?€¢
Crankshaft position (CKP) sensor

Now which part do you want to replace ?

?€¢
Cap and rotor

?€¢
Camshaft position sensor

?€¢
Gear drive and shaft

The camshaft drives the distributor shaft which rotates providing a spark to the correct cylinder by way of the cap and rotor. The camshaft position (CMP) sensor functions much like the crankshaft sensor previously described but provides only a 1x signal to the VCM. That is, for every 2 rotations of the crankshaft, there is 1 rotation of the camshaft. Note that the camshaft position sensor will not affect driveability. The sole purpose of the camshaft position sensor is to provide the VCM with the necessary information for the misfire diagnostic trouble codes (DTCs).

the fuel pump reset switch is on the fuel pump located at the top of the gas tank,(its usually a red or blue reset switch)

• The Camshaft Position Sensor is located on the backside of the engine between the engine and the firewall.
• You will need to jack the car up and preferable put the axles on jack stands.
• Crawl underneath the vehicle to the back of the engine and look up between the engine and the firewall.
• It's a black plastic like sensor with a couple connectors on it.

Regards, Tony

it is the sensor that is being pointed at in the cylinder head

Hi the cam sensor is located just below the water pump to the right

The camshaft position sensor is the distributor on the back top of engine. The crankshaft position sensor is right behind the harmonic balancer on the front of the engine