Question about Cars & Trucks

2 Answers

I have a Phillips RC604 stero in my hyundia 99 model and the balace has shifted to the rear while cleaning the car iand i cant figure out how to get to balance setting

Posted by Chris Onn on


2 Answers


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 99 Answers

Push in or pull out the right buton to adjust the balance. You will fill middle notch when in 50/50 front rear and left right balance

Posted on Apr 23, 2017


Bill Boyd

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 53,816 Answers

Press the mode button it puts you in touch with the operations loke balance front rear , left right, bass, treble etc and readjust the balance setting

Posted on Apr 22, 2017

Testimonial: "There is no mode button thanks bill"

  • Bill Boyd Apr 23, 2017

    maybe it is not labeled a mode button but there has to be a method of switching the balance , bass and treble on or of and adjusting it
    try downloading a user manual for the unit and see how to do it



Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why cant I shift my 99 mercury sable sedan into gears from the steering column anymore? Why do I have to put it on the gear I need, put on the emergency break, then have to get out to shift it into g

Sounds like a shift cable or rod broke. This is dangerous as you probably figured out. Some emergency brakes do not work well for Reverse either. There is so little fabric on the Emergency brake that you are lucky it still works for you.

There is a safety lockout on the gearshift which requires a foot on the brake pedal. Otherwise you could just move the gearshift back and forth and see that the shifter is no longer connected to the transmission.

Look at some autoparts sites for the shift cable assembly. Once you see what is a good assembly you should be able to see where yours is broke. Youtube may have a video to show how to repair your car.

Jul 31, 2014 | 1999 Mercury Sable

1 Answer

Looking for diagram of timing marks for 2004 hyundia santa fe 3.5

What the hack,santa fe shows 2.7 on max...cant get 3.5...
Here is what I got:c2d3ad4f-68a3-4b8c-97fa-aa89eee672eb.jpgCheers,hope u figure out ,share ur solution.

Oct 27, 2013 | Hyundai Santa Fe Cars & Trucks

1 Answer

Hyundia starex auto will not change from 3rd gear

may hav burn a shift solenoid--put car on a scanner--local parts place does it for free--nomerical codes will show and explained in a manual--but bfore replacin a part a more detailed scan shud b performed

Jun 15, 2013 | Hyundai Cars & Trucks

1 Answer

I am tryin to remove the factory radio from a 2000 Nissan Altima and install an aftermarket radio. but i cant seem to figure out a way to get the trim panel around the radio and HVAC module out. And i can...

  • disconnect the negative battery cable from the Altima's battery.

  • 2

    Pry up the trim panel surrounding the gear stick. The trip panel is held in place by plastic clips that will disengage when the panel is pried up. Use a flat-head screwdriver to pry up the panel. The panel doesn't need to be completely removed, just pried up enough to reveal two Phillips screws along the bottom of the radio trim panel.

  • 3

    Remove the two Phillips screws along the bottom edge of the radio trim panel, just above the gear stick. Remove the two Phillips screws from above the radio. Remove the ashtray.

  • 4

    Pry the radio trim panel loose with your fingers or a flat-head screwdriver and remove it.

  • 5

    Remove the four Phillips screws holding the radio in place. Set the screws aside for use later. Slide the radio forward and disconnect the wires from the back of the device.

  • 6

    Slide the cage included with your new stereo into your dash adapter. Slide the stereo into the cage and dash adapter.

  • 7

    Connect the wires from the dash to the back of your new stereo. All stereos have slightly different connections methods, so refer to the owner's manual accompanying your new stereo for the proper connection procedure.

  • 8

    Slide the stereo and dash adapter into the dashboard. Use the previously removed Phillips screws to mount the stereo in place. Replace the radio trim panel and gear stick trim panel. Reconnect your battery.

  • If you are putting a aftermarket stero make sure you buy a stero harness that plugs into the cars harness, on the back side of the harness you just installed will have open wires to conet to your new stero. If you cut the wires from your car to try to splice it to the new raido it can cause problems with the electrical system includeing making the transmission shift or act funny. you can pick the harness at wall-mart, car auido, best buy, or any car auido place.

  • Dec 22, 2010 | 2000 Nissan Altima

    1 Answer

    How do you replace rear disks on a 2008 hyundia santa fe

    take out phillips screws, then repeatedly hit in open area in backside of rotor turn rotor a little bit at a time repeatedly hitting backside of rotor, rust forms on back inside of the rotor. takes some effort!!! but not all that difficult. make sure to clean sliders when doing this and every few months as dirt and debri are cuprit for having to do this repair "they won't tell you that"

    Jun 21, 2010 | 2007 Hyundai Santa Fe Limited

    1 Answer

    I have a '99 Chevy Silverado 1500 4x4. It has a bad vibration in the front-end. I've changed all U-joints and have rotated the tires, but it still has a bad vibration. Does anybody have an idea what the...

    It sounds like you may have lost a weight on one of the tires that balaces it. If so and if you rotated the tires to the rear and rear to front then the vibration would come from the rear. If you only switched the two front tire with each other it would still be in the front. I would start by having the two front tires re-balanced and see what happens. if this doesn't work then it may be a wheel berring going out on you. Keep me informed, Raz

    Apr 18, 2010 | 1999 Chevrolet Silverado 1500

    3 Answers

    2001 Accent, suddenly won't start

    your model doesn't use an Inertia cut off switch for the fuel pump, chances are the fuel pump has just failed, they do that quite often.

    Sep 04, 2009 | 2001 Hyundai Accent

    1 Answer

    99 avenger 2.5 v-6 tranny leaking notice any leaks?

    Sounds as if you have not serviced it with enough fluid. I am a hydraulic specialist and if you give me a little more info...I can help. Those trannys hold more fluid than you think. If you do not service them properly, you WILL have shifting problems and it will look like you are using up fluid. The torque converter is a pig for much fluid was drained out?

    And, I understand you DID NOT take anything else off but the filter correct?

    Mar 13, 2009 | 1999 Dodge Avenger

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    48 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts


    Level 3 Expert

    85239 Answers

    john h

    Level 3 Expert

    23590 Answers

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    6576 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides