Question about Chevrolet HHR

1 Answer

What are torque specs for caliper in 2007 Chevy HHR

Posted by Brenda on

Ad

1 Answer

jack layton

jack layton

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,345 Answers

The two pin bolts that hold the caliper? My info says 25 ft lbs.

Posted on Apr 19, 2017

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: CAR BATTERY FOR CHEVY 2007 HHR

Your battery is located in the rear under your cargo floor. Where most cars would hide a compact spare.

Posted on Dec 22, 2008

Ad

Anonymous

  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

Anonymous

  • 33 Answers

SOURCE: Need the correct torque specs for 2004 silverado 1500 calipers

  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps

    • Posted on Mar 28, 2009

    GIVHRR

    • 72 Answers

    SOURCE: Front Hub Bearing Torque specs to complete replacement

    THE LUG NUT TORQUE SPEC - 140FT/LBS\
    CALIPER MOUNT - 80FT/LBS
    CALIPER BRACKET 129FT/LBS
    AXLE NUT 177FT/LBS

    Posted on May 09, 2009

    Anonymous

    • 1 Answer

    SOURCE: torque specs

    2005 Chevy 1500 4x4 front hub bearing assembly, what is the torque spec

    Posted on Jun 29, 2009

    Add Your Answer

    ×

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Torque specs on 2006 hhr 2.2 liter
    Torque specs for what part, cylinder head or something else? Can you be more specific?

    Jul 18, 2017 | 2006 Chevrolet HHR

    0 Answers

    06 HHR front brakes apply themselves, this car has no abs. I've changed. calipers, master cylinder, brake booster, pads, rotors, and front brake hoses.

    Jul 08, 2016 | 2006 Chevrolet HHR

    1 Answer

    What is the front brake and caliper torque spec for a 2007 Honda fit
    Don't be too fussy with torque specs, as long as it's tight you will be fine. Use a breaker bar, not a impact gun as they are unreliable. Torque settings are only really important when building engines (head bolts etc)

    Sep 06, 2015 | Honda Cars & Trucks

    1 Answer

    What is the torque specs for brake calipers on a ford explorer sport front calipers

    1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

      www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
      Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
      5 posts
      Mar 12, 2009
      05 F250 brake torque specs please
      6 posts
      Aug 22, 2007
      Brake caliper torque specs
      5 posts
      Jul 14, 2007
      Front brake Caliper Bolt Torque
      6 posts
      Apr 25, 2005
      More results from www.thedieselstop.com

    Jul 11, 2015 | 1998 Ford Explorer

    1 Answer

    How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?
    First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

    May 10, 2014 | 2007 Saturn Aura XR Sedan

    1 Answer

    Need to remove the front wheel bearing hub on a 2007 dodge nitro
    Remove the brake caliper and pads, You have to remove the large axle nut It has to be torqued back on. You can find that torque spec by googling axle nut torque spec for your vehicle. Disconnect the ABS wire if it has it then the bearing will have 3 bolts on the backside to remove, They should be torqued back on as well. Dont forget to use a jack stand and leave the jack up as well for extra safety

    Apr 20, 2014 | 2007 Dodge Nitro R/T New Cars

    1 Answer

    2008 CHEVY HHR TORQUE SPECS FOR HEAD

      DO NOT use any sealing material.

    1. Install the cylinder head gasket.
    2. Install the cylinder head.
    3. Install NEW cylinder head bolts.

      4. Caution!Refer to Fastener Notice in Cautions and Notices.

      412510.gif
      Click to Enlarge

    4. Install and tighten the cylinder head bolts in the sequence shown.

      5. Tighten
      Tighten the bolts to 30 N•m (22 lb ft) plus an additional 155 degrees using the J 45059 .

      412425.gif
      Click to Enlarge

    5. Install the NEW front cylinder head bolts.

      6. Tighten
      Tighten the bolts to 35 N•m (26 lb ft).

    /f 412425.gif412510.gif

    Feb 19, 2013 | 2008 Chevrolet HHR 2.2

    1 Answer

    Need torque settings for front calliper bolts on 2009 Chevy HHR
    ive done millions of brakes and callipers not once have i torqed to specs on cllipers just tighten till its tough but not to hard or youll snap a bolt..

    Sep 29, 2012 | 2009 Chevrolet HHR

    2 Answers

    Front Hub Bearing Torque specs to complete replacement
    THE LUG NUT TORQUE SPEC - 140FT/LBS\
    CALIPER MOUNT - 80FT/LBS
    CALIPER BRACKET 129FT/LBS
    AXLE NUT 177FT/LBS

    Apr 24, 2009 | 2003 Chevrolet Silverado 1500

    1 Answer

    CAR BATTERY FOR CHEVY 2007 HHR
    Your battery is located in the rear under your cargo floor. Where most cars would hide a compact spare.

    Dec 22, 2008 | 2007 Chevrolet HHR Special Edition

    Not finding what you are looking for?

    View Most Popular

    Cars & Trucks

    Related Question

    Torque specs on 2006 hhr 2.2 liter

    • 2006 Chevrolet HHR

    Open Questions:

    0 Answers

    2000 4x4. My car don't want to start. Please help.

    Jan 15, 2021 | 2000 Chevrolet Tahoe

    0 Answers

    Where is wiper fuse?

    Jan 14, 2021 | 1985 Chevrolet El Camino

    0 Answers

    2.2l. What is firing order and torque settings for head bolt, rocker arm, valves and timing chain?

    Dec 31, 2020 | 2010 Chevrolet HHR

    0 Answers

    Sedan flex fuel. After installing fuel pump, how can I restart?

    Dec 30, 2020 | 2010 Chevrolet Impala

    Cars & Trucks Logo

    Related Topics:

    301 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    2009 Chevrolet HHR 2.4

    2008 Chevrolet Hhr

    2006 Chevrolet HHR

    2006 Chevrolet HHR

    2011 Chevrolet HHR

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    john h

    Level 3 Expert

    23515 Answers

    Joe Taylor
    Joe Taylor

    Level 3 Expert

    2228 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    2007_chevrolet_hhr_owners.pdf....

    2007 Chevrolet HHR...

    Loading...