Question about 1998 Mitsubishi Eclipse

Open Question

Replace 1998 Mitsubishi Eclipse camshaft sensor 2.0 turbo gst

Posted by Dan dier on

Ad

5 Related Answers

dustyboner

alex metro

  • 364 Answers

SOURCE: 95 eclipse MAF bypass?

if you want to get rid of your MAF sensor, you will need to upgrade your engine management. there are a few piggy-back systems like MAP-ECU . you could also go with a stand-alone system like the AEM EMS

Posted on Nov 06, 2008

Ad

Anonymous

  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

Ad

Anonymous

  • 135 Answers

SOURCE: Where is bank1 sensor 1 (O2 sensor) of 2003 Mitsubishi Eclipse

if its a 4 cylinder it will the 02 sensor closest or if not in the exhaust manifold

Posted on Aug 05, 2009

Anonymous

  • 27 Answers

SOURCE: need the vacuum hose diagram for a 1998 mitsubishi eclipse

http://www.dsmtuners.com/forums/attachments/420a-bolt-tech/89827d1228187918-resolved-need-vacuum-line-help-fast-420aturbovac-boostlinesstock.jpg
hope this helps

Posted on Oct 21, 2009

Anonymous

  • 18 Answers

SOURCE: 1997 mitsubishi eclipse gst wont start it looks

Remove the bottom of your back seat. Turn the ignition on without cranking the car. You should hear the fuel pump prime for a few seconds and shut off. If you don't hear that sound, there are two relays on the right side of the firewall next to the master cylinder that are part of the fuel system. I had one go bad on me (the contact corroded) and didn't know which one it might be so I bought the cheaper of the two. Haven't had a problem since!

Posted on Jan 13, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TIMING BELT SCHEMATIC ON A 1999 MITSUBIHI ECLIPSE 2.0


Since you didn't specify if you had the turbo or non-turbo engine, i'll give you links to both.
2.0L non-turbo (420a) RS/GS
2.0L turbo (4g63) GST/GSX

Sep 04, 2010 | 1999 Mitsubishi Eclipse

2 Answers

How install the timming belt in my mitsubishi eclipse gst turbo 98


this link has a step-by-step DIY for changing the timing belt on your car. 2G TURBO TIMING BELT PROCEDURE

Jun 20, 2010 | 1998 Mitsubishi Eclipse

1 Answer

1998 mitsubishi eclipse GS 2.0 non turbo automatic,


Have you changed the spark plugs and fuel filter yet?

May 27, 2010 | 1998 Mitsubishi Eclipse

1 Answer

ON MY 97 ECLIPSE GST WON'T


Is there oil in the turbo?

Feb 26, 2010 | 1997 Mitsubishi Eclipse

1 Answer

How will the car run if sparks are bad


the engine will misfire, consume more gas, run roughly. it's better to replace all the spark plugs

Sep 22, 2009 | 1997 Mitsubishi Eclipse

1 Answer

I have a 96 mistubishi eclipse with 2.0 non turbo that has a code p1391 can anyone help me please?????????


Tests/Procedures: 1. Check the Crankshaft Position Sensor (CKP) and Camshaft Position Sensor (CMP) signals with a lab scope.

2. Check the wiring and connections at the CKP and CMP sensor. Potential Causes: Camshaft Position Sensor (CMP)
Crankshaft Position Sensor (CKP)
Powertrain Control Module (PCM)
Wiring

Aug 08, 2009 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Timing my 1998 Mitsubishi Eclipse GST


the timing marks on your crank and cam crank need to be one on top of the other if you understand what i mean. anyway if this is done correctly, your cam should make two revolutions to one of the crank thus after one full revolution of the crankshat gear your camshaft gear should do 2 revolutions and you timing marks should be next to one another

Jan 08, 2009 | 1998 Mitsubishi Eclipse

1 Answer

95 eclipse MAF bypass?


if you want to get rid of your MAF sensor, you will need to upgrade your engine management. there are a few piggy-back systems like MAP-ECU . you could also go with a stand-alone system like the AEM EMS

Nov 03, 2008 | 1996 Mitsubishi Eclipse

1 Answer

Replacing the bumper of my car


http://www.rcaz.com/rcaz/sub%20indexes/eclipsebumper/bumper.a.htm 
It has step by step instructions with pictures. Even though its for an RS, which is what yours is, I used it for my 98 Eclipse GST. And its pretty much easy.

Aug 30, 2008 | 1998 Mitsubishi Eclipse

Not finding what you are looking for?
1998 Mitsubishi Eclipse Logo

Related Topics:

193 views

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Thomas Perkins
Thomas Perkins

Level 3 Expert

14869 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

john h

Level 3 Expert

23888 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...