Question about 1993 Isuzu Rodeo

Open Question

Does a 1993 rodeo isuzu have a kill switch. ?

Posted by Kathy Hayes on

Ad

5 Related Answers

Anonymous

  • 3 Answers

SOURCE: power windows isuzu rodeo 1999

Cable must of disconnected need to take door cover off and reconnect...

Posted on Jan 10, 2009

Ad
yobo007

yobo007

  • 515 Answers

SOURCE: 1993 Isuzu Rodeo engine tick

The stalling cound be your idle control; on the throttle body. The ticking noise is either from the timing belt hydralic tensioner or a valve lifter. If you hear the ticking in the front of the engine on the 3.2 v-6 it is most likely the tensioner. As for changing the timing belt it is a very involved process ( I've done it many times ). Everything on the front of the engine comes off including the engine balancer on the crankshaft.
The idler pully and belt tensioner are located at the bottom of the engine near the crank on the passenger side of block. Now there are two cams, water pump ( Change that also when you are down there ), crank pully to run the belt over. There are timing marks on the cover plate behind the cam pullies and one on the crank a notch that lines up on the oil pump cover. REMEMBER THIS DO NOT MOVE THE CAMS AND CRANKSHAFT WHEN YOU HAVE THEM LINED UP. If you are not sure get the manual and get a good friend who is a good mechanic. This it an advanced repair job; you mess up the timing and you will bend valves at the minimum..

Posted on Feb 11, 2009

Ad

Anonymous

  • 365 Answers

SOURCE: 1997 Isuzu Rodeo, 4.2L All windows stopped working!!!

all windows controlled from the drivers door...if you have someone in the family with BIG fists have them stand beside the drivers door panel and putting the **** against the door, SLAM their fist into the door panel right under the switches. Take a can of WD-40 and spray ALOT directly around the switches in the door using the little red hose WD40 gives you. GM's are known for carbon-tracking their door mechanisms...build up over the years...sometime banging the door knocks the buildup loose allowing the circuit to work.

Posted on Jun 14, 2009

scj103

  • 104 Answers

SOURCE: 1993 Isuzu Rodeo

Have a look under the front of the transmission column/dash near the pedals. theyre usually there, tucked behind the trim. Not attached to anything, just on the end of wires. And you usually need a Tech-II diagnostics machine for any Isuzu kit, as even the likes of Snap-on won't read it.
:(

Posted on Jul 12, 2009

Anonymous

  • 571 Answers

SOURCE: what is the radiator cooling system capacity for a

2.6L 4-cyl Engine: 9.5 quarts
3.1L 6-cyl Engine: 12 quarts

Posted on Dec 13, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the obd port on my 1993 isuzu Amigo


wow no engine size stated, and MATTERs.!
with no tech1 or 1a scan tooL (real scan tools)
what good is DLC?>
sure jumper CODES< (DTC errors in todays parlance)
there is abs tool.. but only on some cars.

and more. read the FSM yet?
lets pretend you said how do i get the PCM flash error codes
easy jumper the DLC. 'diag, link connector"

google Isuzu DLC jumpers, nets you all this.

http://www.troublecodes.net/isuzu/

there is no world standards for OBD1 so DCL are
every freakn where.

in cab or engine bay or like hondas, on PCM casiing
wild and wolly DLC>


quote

Multi-Port Fuel Injection

Amigo,Trooper II , Rodeo & Pickup
On Rodeo, Amigo, and Pickup (except 1993-95 models W/3.2L engine), connect the single wire diagnostic leads located behind the left hand kick panel together. On 1993-95 Rodeo models W/3.2 engine, the data link is located under the left hand side of the instrument panel. On all models, turn the ignition switch to the On position. At this point, the "Check Engine" light should flash. codes


25011203-uqsqk1sqel1nykdqv4diatnw-3-0.jpg 12pin version below.
jump pins,(for PCM errors) pins A > B
25011203-uqsqk1sqel1nykdqv4diatnw-3-1.gif
the codes are here.
http://www.troublecodes.net/isuzu/iszucel/





25011203-uqsqk1sqel1nykdqv4diatnw-3-3.jpg see no in the engine bay at all, like the 1 guess

Aug 26, 2014 | 1993 Isuzu Amigo

1 Answer

1993 isuzu rodeo winter mode not engaging


the plugin to the winter drive switch in console has come lose. had the same problem in my rodeo. if the dash light isnt coming on then its unpuged.

Dec 17, 2012 | 1993 Isuzu Rodeo

1 Answer

Schematic for 1993 isuzu rodeo 3.2 l engine ignition coil pack placement


i not sure where to refill the clutch fluid as nothing is marked on my 93 isuzu rodeo. i have no pressure in my clutch any suggestions?

Jun 17, 2010 | 1993 Isuzu Rodeo

1 Answer

1993 Isuzu Rodeo


Have a look under the front of the transmission column/dash near the pedals. theyre usually there, tucked behind the trim. Not attached to anything, just on the end of wires. And you usually need a Tech-II diagnostics machine for any Isuzu kit, as even the likes of Snap-on won't read it.
:(

Jul 11, 2009 | 1993 Isuzu Rodeo

2 Answers

2000 isuzu Rodeo wont start


Could be your neutral safety switch, or it's not all the way in park. Broken or loose wires in the starting circuit. Inspect all wires and connectors at the battery, starter solenoid, and ignition switch. Or your starter pinion is jammed in the ring gear. Remove starter and inspect. Last but not least, your engine is seized. You don't want that one. Good luck.

May 22, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...