Need to change stop/tail lamp on Scenic dci 2011. I've removed the two visible screws but the light cluster will not move! Can you help please?

TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

the switch is malfing.

1. You fix it.?
2. replace it.
3. get help (hands on)
4. have it fixed.

Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

undo the hatch back {life the tail up as if you were wanting to gain access to the boot ..you will notice on either side both lighting clusters .depending on what side needs replacing .all you have to do it use a size 2 Philips screw driver to remove the black screws holding in the lighting clusters the locate the broken lamp{bulb} then twist the holder half a turn then replace the lamp {bulb} and then refit the cluster ..PLEASE note when you remove the screws you will have to gently ease the lighting cluster away from the body of the vehicle as if you try to rip it of you will damage it .there are two lugs that slide in to the bodywork of the car .make sure that you take a little time to locate them and check that the lighting cluster fits nicely to the vehicle before you replace the screws ..its worth trying the replacement lamp/bulb before you replace the screws ..just in case you have replaced a fault one with a faulty one !!! it can happen .

Tail Lights

1. Open the endgate or liftgate.
   

2. Remove the screws that retain the tail lamp assembly to the vehicle.
   

   Tail lamp assembly removal
   

3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.
   

4. Remove the bulbs from the sockets.
   

To install:

1. Install the bulbs into the sockets.
   

2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.
   

3. Install the tail lamp assembly to the vehicle.
   

4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).
   

Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation

1. Remove the tail lamp assembly retaining screws from the body.
2. Release the locking pins by pulling the assembly directly rearward.
3. Disconnect the tail lamp assembly connector.
4. Remove the tail lamp circuit board from the assembly.

To Install:

1. Install the tail lamp circuit board into the assembly.
2. Connect the tail lamp assembly connector.
3. Push the assembly directly forward into the opening to engage the locking pins.
4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).

High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.

1. Raise the liftgate.
2. Lower the rear of the headliner by removing the rear headliner pins.
3. Disconnect the high mount stop lamp connector.
4. Remove the high mount stop lamp grommet from the body.
5. Lower the liftgate.
6. Open the liftgate window.
7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
8. Remove the high mount stop lamp from the vehicle.

To Install:

1. Place the high mount stop lamp onto the vehicle.
2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
3. Close the liftgate window.
4. Lift the liftgate.
5. Install the high mount stop lamp grommet into the body.
6. Connect the high mount stop lamp connector.
7. Install the rear of the headliner by inserting the retaining pins.

High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp

1. Disconnect battery negative cable.
2. Disconnect high mounted stop lamp electrical connector from inside trunk.
3. Remove package tray.
4. Replace bulb from package tray.

To Install:
High Mounted Stop Lamp

1. Install package tray.
2. Connect high mounted stop lamp electrical connector from inside trunk.
3. Connect battery negative cable.

I had the same problem go to ECUTESTING.COM the cluster is very simple to remove. Carefully unclip/prise the direct surrounding from around the cluster and then unplug the wiring (2 plugs on the front) now unscrew the 2 screws on each end and gentle remove the digial cluster unit. ABOUT A 10-15MINS JOB. All this can be done sitting in your drivers set.Send it to the above cost about £195 and they'll send it back with a 2yr warrenty. Dealer charges in the region of £400.

If you're asking how do you change a taillight bulb, then follow this procedure:

Open the trunk lid.

Disconnect the connectors from the taillights (taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps.) There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.


Brake Lights/Taillights: 21/5 W

Rear Turn Signal Light: 21 W

Back-up Light: 21 W

Rear Side Marker Light: 5 W


Turn the bulb sockets 45 º counterclockwise to remove the bulbs.


If you're removing the taillamps with the bumper off there are 3 nuts and screws that hold the taillight to the rear panel of the car that have to come off from the inside of the trunk.
Remove the nuts and screws, then remove the taillight.

hope that answers your question