Question about 2001 Mitsubishi Eclipse

Open Question

Adjust shift cables on 2001 eclipse Manuel tranny how

Posted by Steve Gill on

Ad

1 Related Answer

super_guy

  • 1986 Answers

SOURCE: Adjusting Headlights w/2001 Eclipse?

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 mitsubishi eclipse v6 how to remove clutch


drop the tranny and it will be right there

Jul 30, 2010 | 2001 Mitsubishi Eclipse

2 Answers

Transmission?


sorry, first guess is that your transmission oil pump went out and now you have no pressure to operate the clutches inside the tranny, second is the tranny is "burned' which happens when the transmission filter and fluid were not replaced within a reasonable amount of time and the surface of the clutches started getting worn off,, you would have noticed as you would loose power (acceleration) or not shifting properly over a period of time. unfortunately either one requires removal of the transmission and replacing the components inside..

Apr 15, 2010 | 2001 Mitsubishi Eclipse Spyder

1 Answer

2001 jeep grand cherokee wont shift out of first, no slipping, reverse park neutral ok. i replaced govenor solenoid and transducer, what else should i look at


Check shift cable. Disconnect cable at tranny and move linkage by hand then reconnect cable and see if the cable moves the linkage the same amount.

Jan 18, 2010 | 2001 Jeep Grand Cherokee

3 Answers

2001 eclipse suddenly quit driving, acts like it slipped into neutral and shifting makes no difference (auto). Any ideas on what happened?


its the same thing eclipse trannys have a big problem with the wave spring inside, it breaks and destroys the ******, If you get it fixed again make sure they put a rebuilt one in. Mitsubishi redesigned the wave spring

Nov 30, 2009 | 2001 Mitsubishi Eclipse

1 Answer

I have a 2001 Mitsubishi Eclipse Spyder GT. the


check your tran fld if its up something broke in your tranny it will have to be pulled and repaired or raplaced

Jul 12, 2009 | Mitsubishi Eclipse Spyder Cars & Trucks

1 Answer

Shifting from first to second jerks truck hard


Check fluid level in tranny. what kind of tranny? 700R4- Re adjust the TV cable, 4L60E- Shift Solenoid may be on its way out.

May 28, 2009 | 1994 Chevrolet K1500

2 Answers

Shifting column is not working properly, tranny is ok


Take the cable or linkage off the tranny. Push the tranny arm into park. If it is a linkage then adjust your linkage to match to tranny arm. If it is a cable with it disconnected see if it moves when you move the gear shift, The cable should move freely. You can pull on the end of the cable to make sure it is not broken. Make sure that your tranny arm moves in all gears. Please chalk the wheels so you don't get hurt.

Mar 29, 2009 | 1994 Ford Aerostar Extended

2 Answers

My 1993 mitsubishi eclipse wont go into 5th gear


1st and 5th are the most stressed gears and the mitsubishi how ever fluid level and also adjusts ments are also possible issues i would check fluid levels as previously stated then adjust the shift cables becaause over time they do stretch and if it is stretched enough it will not allow a full engaement of the gears which can cause grinding or just no power if both of thos dont work look to internal parts like synchros a total shaft replacement will not be the case as the gears are paired on shafts but 1st and 5th are not paired together has there been anytype of work on or around the tranny

Mar 24, 2009 | 1993 Mitsubishi Eclipse

Not finding what you are looking for?
2001 Mitsubishi Eclipse Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...