Hummer H2 2004 Driver seat dead and both front heater on seats are dead seat stopped over the bolts securing to body. need to move seat back or forward to get to mounting bolts Thank you John

Hope this video helps.

Not a fuse issue , more then likely a burnt heating element in the seat , happens all the time .
Heated Seat Components
The heated seat system consists of the following components:
• Driver and passenger heated seat switches
• Driver and passenger seat back heater elements
• Driver and passenger seat cushion heater elements
• Driver and passenger seat back temperature sensors
• Driver seat module
• Driver door module
• Passenger door module

The control module have a Battery voltage supply , the module supply's voltage to the seat heating elements .
The heated seat switches are momentary contact switches and are inputs to the driver and passenger door modules. Battery voltage is supplied to the switch assembly from the door module, and when a heated seat switch is pressed and released a brief switch signal voltage is supplied to the door module. Whenever the door module receives an active heated seat switch input, the next heated seat operating mode is determined by whatever the current mode may be. The seat heater elements are controlled by the driver seat module using inputs from the door modules through Class 2 serial data circuit messages. The driver seat module controls the voltage supply and the ground circuits to the seat heater elements. When a heated seat function is commanded active, the seat module will switch battery voltage to the heater element supply circuits, and ground is provided through low side drive control circuits. During heated seat operation both the seat back and cushion heater elements are supplied battery voltage. The seat module grounds the appropriate control circuits for back only or back and cushion heating modes, and opens or closes the active control circuits as necessary in order to maintain the desired seat temperature. The seat module relies on inputs from thermistors located in the driver and passenger seat backs to control heated seat temperatures. The thermistors are 2 wire sensors supplied with a 5-volt referenced signal circuit and a low reference circuit from the seat module. Resistance through the thermistors varies with temperature causing the heated seat sensor signal circuit voltage levels to decrease as the seat back temperatures rise. The seat modules allow heated seat operation only while the engine is running which is determined by a Class 2 serial data circuit message from the powertrain control module.

Your best bet , take it to a qualified repair shop.

Remove the plastic caps covering the legs and the bolts into the body once you remove plastic covers caps you will be able to see the bolts clearly, carpeting might be camouflaging both sides. And on a side note when removing chair make sure you disconnect the electrical clip for the seatbelt indicator

What make vehicle ? you have H2 at the top they show a SEAT . H2 hummer ?

Auto Repair: How to Replace a Power Seat Motor - YouTube

? 1:44
https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - ‎7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che

1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

the seat adjuster assembly is bad. i was a chrysler tech for 15 years. the motor that runs the forward and back is either bad or the tracks are bad and it is binding. you can not get parts for it. you will have to buy a new complete adjuster or see if a boneyard may have a good used aseembly. Don

put the seat in the full back position remove the two front bolts securing it to the floor, move it all the way forward now, remove the two rear bolts securing it to the floor now tip the seat back allowing it to rest on the back seat. make sure there is no additional wiring plugged in. use the recline function the make the seat flatter, now with two people roll the seat and remove throught the front door utilizing the rear for the helper

Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6

1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
   

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips

1. Remove upper rear seat back-to-chassis bolts.

Fig. 4: Remove the bolts behind the center armrest ...



Fig. 5: ... and the bolts on the lower corners ...



Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat

1. Remove rear seat back by tilting forward and pulling straight up.
   

To install:

1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal

1. Remove rear seat cushion. Refer to Section 01-10 .
   

Seat Cushion, Rear Sedan
Removal

1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
   

1. Remove rear seat cushion from vehicle.
   

1. Remove rear seat back. Refer to Section 01-10 .
   

Seat Back, Rear 60/40 Split Bench—Sedan
Removal

1. NOTE: Safety belt bolts do not secure seat back to vehicle.
   
   Remove rear seat cushion as described.
   

1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
   

1. Remove two bolts from outboard rear seat back frame retaining brackets.
   

1. Lift seat back up and pull forward to remove from vehicle.
   

1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
   

Trim Panel, Quarter—Sedan Removal

1. Remove rear seat. Refer to Section 01-10 .
   

1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
   

1. Pull lower quarter trim panel away from body.
   

1. Remove safety belt retaining bolt.
   

1. Feed safety belt through lower quarter trim panel.
   

1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
   

1. Remove retractor anchor nut and retractor from rear quarter panel.
   

1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
   

1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
   

1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
   
   
   
   
   
   Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)

1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
   
   
   
   
   

Installation

1. To install, reverse Removal procedure.
   

1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
   

1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
   

1. Check the restraint system for proper operation.