Question about 1998 Chevrolet Malibu

Open Question

Program new remote for 98 malibu.

I can't find the programming connector anywhere. looked in center of rear shelf and right side tail light harness.

Posted by Anonymous on

Ad

5 Related Answers

reichweinj

Joseph Reichwein

  • 71 Answers

SOURCE: 2006 Chevy Trailblazer Tail Lights

There was a recall on this, take to the dealer and they will replace the whole socket on this.

Posted on Nov 10, 2008

Ad

SOURCE: Tail lights don't work on 1998 Chevy Silverado.

check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Posted on Feb 17, 2009

Ad

Anonymous

  • 206 Answers

SOURCE: program a keyless enrty remote start 2004 chevy malibu

Dealer only If you find a different means let me know

Posted on Apr 08, 2009

Jonah Oneal

  • 14092 Answers

SOURCE: 1995 chevy silverado z71 no power to right tail light

check fuse.if good you got grounding problems or faulty turn signal switch.

Posted on May 09, 2009

Anonymous

  • 181 Answers

SOURCE: 2008 chevy malibu. how to program keyless entry remote

You must take it to the Chevy dealer.

Posted on Mar 09, 2010

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless Remote Module for 1998 Chevy Malibu


Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the negative battery cable.
Open the rear compartment lid.
Remove the remote door lock receiver (2). The receiver (2) is located between the rear package shelf and the rear package shelf cover, to the right of the center access hole. Compress the 4 tabs and slide the receiver (1) down through the access hole.
Disconnect the electrical connector (1).

Dec 08, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

I have a 98 chevy malibu. the tail lights, running lights and instrument lights do not work but head lights do


The good news is that all of these problems stem from the same source: the 15A PARK LPS fuse in the underhood wiring harness junction block. When you set the turn/headlamp/wiper switch to PARK, the park lamp relay in the junction block closes and power is applied to the front marker lamps and the park filament of the front park/turn lamps as well as the tail filaments of the rear tail/stop lamps.

As for the instrument lights, that same PARK LPS fuse applies power to the same turn/headlamp/wiper switch that, when set to PARK or HEAD applies power to the variable panel dimmer switch which lets you set the illumination level. Switch output is applied to the lamp dimmer module and module output passes through the 10A INST LAMPS fuse in the right I/P wiring harness junction block to the instrument lamps

Oct 13, 2012 | 1998 Chevrolet Malibu

1 Answer

Only left tail light does not work. left break light works fine. All other lights work. New bulb, good fuse, and new connector that the bulb plugs into. I can ground the middle wire going into the...


poor ground, check the wire harness, this is the one that comes from front of vehicle to the rear and plugs into the wires that go to the rear lights. trace the wire coming out of the light itself and eventually you will see that it comes to a connector that attaches to the wiring harness.

Sep 03, 2010 | Ford Windstar Cars & Trucks

2 Answers

NEED TO REEPROGRAMING A REMOTE CONTROL FOR A MALIBU 1998 HOW '?


1. Make sure ignition is in the OFF position.
2. Locate the Programming Connector in the trunk (center of rear shelf). It is a plastic connector with
two wires leading up to it. The connector is not plugged into anything. You may have to pull back
trim to access the connector.

3. The programming connector should have two terminals. Connect both terminals with a suitable
jumper wire. The Keyless Entry Module will lock then unlock all the door lock motors once. Make
sure the terminals remain connected throughout the programming procedure.

4. Press and hold the LOCK and UNLOCK buttons on the transmitter simultaneously for at least 15
seconds or until the vehicle automatically locks and unlocks the door locks. Your new remote has
been accepted and all existing remote codes have been erased.

5. Repeat the previous step for each transmitter to be programmed. Do not remove jumper wire in
between programming of transmitters.

6. Remove the jumper wire from the Keyless Programming Connector.

Dec 15, 2009 | 1998 Chevrolet Malibu

1 Answer

How do you change tail lights for the 2003 passat


Rear Turn Signal, Brake and Parking Lights Removal & Installation To Remove
  1. Remove or disconnect the following:
    • Harness connector
    • Combination nuts
    • Lamp and its assembly toward rear
To Install:
  1. Install or connect the following:
    • Lamp and its assembly into position
    • Combination nuts; torque to 35 lb-in. (4 Nm)
    • Harness connector
This is the only thing the tech manual says.

Jul 22, 2009 | 2003 Volkswagen Passat

2 Answers

2006 chev malibu fuses where are they automatic mirror adj, cig lighter and right rear tailight (Break)


theres a fuse box under the rear driver side tail light, open the trunk theres a small space to for storage, look underneath it u'll see a "door" open then look for a black box. it flips down, it has ur basic fuse, tail lights, **** like that, all other major ones like horn are under the hood between the driver fender and the battery

Jun 03, 2009 | 2006 Chevrolet Malibu

2 Answers

Change Dodge Ram tail lights from 2005 to new 2008. The wiring harness to change from the 05 to the updated 08 are different. Is there a adapting wire harness from dodge for this?


I just got a pair of 2008 tail light lens for my 2002 Dodge Ram 1500. If you look under the rear there is a connector that runs up to the tail light. This is a small harness. I believe that all you need to do is purchase the 2008 tail light harness. It looks like it will snap into the bottom of the stock harness and will fit the 2008 lenses.

Feb 20, 2009 | 2005 Dodge Ram

1 Answer

PROGRAMING ALARM REMOTE ON 95 TAHOE


Here it is straight from Alldata:
  1. Ground pin G of the Data Link Connector (DLC).**Bottom left pin**
    • Receiver will respond by locking, and unlocking doors within 2 seconds.
  1. Press any button of the first transmitter to be programmed.
  2. The control module will respond by locking/unlocking doors and activating rear window release.
  3. Press any button of the second transmitter to be programmed (if used).
  4. The control module will respond by locking/unlocking doors and activating the rear window release.
    1. Remove the ground applied to the reprogrammed connector.
      1. Transmitter operation is verified locking and unlocking the doors and activating the rear window release

Dec 23, 2008 | 2007 Chevrolet Malibu SS Sedan New Cars

3 Answers

1993 Supra tail lights not working


there is a switch located on the brake pedal right at the bend(just behind where your foot touches)

Oct 22, 2008 | 1993 Toyota Supra

1 Answer

Programing keyless entry


If you have an owners manual the programming instructions are in there. If no manual here they are:

1. Turn the ignition off.
2. Ground the receiver program terminal. Jump the two terminals located in the programing ground connector. (What this means in simple terms is locate the wires that run on the right side of the trunk. There is two black wires that has a plug on the end with two prongs. It is in between the antenna and tail lights.)
3. Within 2 seconds of connecting the prongs the door locks will lock. The unlock and the rear compartment lid release will produce a cycle, causing the horn to chirp. This indicates that the module is ready for reprogramming.
4. Press and hold the lock and unlock buttons at the same time until the doors lock and unlock. The rear compartment lid will release and the horn sounds to indicate that the transmitter has successfully been reprogrammed. (Hold buttons down for approximately 12 seconds)
5. Repeat the previous step for the remaining transmitters.
6. Remove the jumper at the program connector.
7. Verify the proper operation of each transmitter

Sep 30, 2008 | 2007 Chevrolet Malibu SS Sedan New Cars

Not finding what you are looking for?
1998 Chevrolet Malibu Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...