Should be attached to throttle-body. two wire connector, wire colors, red, and white with lite blue tracer.
SOURCE: 2007 Mercury Grand Marquis required oil weight
If u have a moderate climate, 10W-30W, if cold climate 5W-30W, do not use any heavier weight of oils.
SOURCE: IAC Valve Location - 1996 Jeep Grand Cherokee
The idle air control valve is located on the back of the throttle body. It has an oval electrical connector and two torx screws holding it in. Unplug the connector, remove the two screws then lightly tap the body with a soft faced mallet to loosen it from the body.
Once you have it out and prior to installing a new valve clean the seat inside the throttle body where the idle control fits. This must be very clean! Installation is in the reverse order.
To save some cash, pull the valve out and clean it with throttle body cleaner, this usually fixes the problem for quite a while.
Good luck and hope this helps.
SOURCE: how to remove the egr valve on a 1993 mercury
Jack up the passengers side of the car, get a 1 1/16" wrench break loose the fitting to the manifold, hold a 24 mm wrench on the fitting to the manifold, loosen the flare nut on the tube. Then using a 10 mm socket, about 2 inches long, loosen the two nuts under the EGR valve, then take the both out, remove the vacuum hose to the top of the EGR valve, and the sensing line from the small tube. then completely remove the flare nut from the orifice fitting on the manifold. BE CAREFUL with the tube, do not bend it or break it, you may find PB blaster useful the night before on a cold engine loosen these fittings. Once the EGR valve is out, remove the orifice out of the manifold, remove the tube from the EGR valve, again be careful, mark the tube to EGR position before pulling this off, because the top fitting to EGR needs tightened before you put it back in, it will make the lower fitting difficult if you do not line it up right, dry fitting from under the car is helpful, mark it, and then tighten the top. Clean out the tube, be careful not to bend the little tube, either inside or outside the larger tube, it sticks out inside. Clean the orifice, clean the manifold face carefully not to score it, check for blockage there too. Apply anti-seize to the orifice, put it back in the manifold, then apply anti-seize to the bolts for the EGR valve, and the flare nuts both ends. Apply some silicon to the EGR valve face, just enough to hold the gasket in place, put the new gasket on, start the bolts two turns in the gasket, it will hold them in place, then start them in the manifold, then start the lower flare fitting to orifice, tighten the top bolts, and then the flare nut, connect the vacuum line, connect the sensing line. I just recently did this process, it works, if have other EGR issues, the valve is the easiest.
SOURCE: what is the spark plug gap specification for a
go to or call an auto pARTS STORE they can tell you the plug gap.
SOURCE: how to replace starter +1993 Mercury Grand Marquis
disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,
OPERATION
The Idle Air Control (IAC) valve adjusts the engine idle speed. The valve is located on the side of the throttle body. The valve is controlled by a duty cycle signal from the PCM and allows air to bypass the throttle plate in order to maintain the proper idle speed.
Do not attempt to clean the IAC valve. Carburetor tune-up cleaners or any type of solvent cleaners will damage the internal components of the valve.
TESTING
See Figure 1
Fig. Fig. 1: The IAC can be monitored with an appropriate and Data-stream capable scan tool
REMOVAL & INSTALLATION
Fig. Fig. 2: IAC solenoid location-4.6L engine
Hi jabddbb, here is a picture of the IACV for 92-95 Grand Marquis hope this helps you :)
948 views
Usually answered in minutes!
×