I can't upload the diagram but the firing order appears to be 1,4,6,3,2,5

Install the spark plug wire(s) (1, 3 and 5) to the engine right side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

Install the spark plug wire(s) (2, 4 and 6) to the engine left side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

You can get a copy of the service manual from Promanuals.net for cheap.

Posted on Sep 26, 2009

Anonymous

2 Answers

SOURCE: how do t replace the alt. in a 2000 olds

Remove the two front motor mounts mounted on the frame above the radiator.This is not a weight bearing mount it is for vibration. The engine will not move much once removed. Ratchet the motor forward using a ratcheting strap hooked to the black arm that extends above the motor located on the right side. Remove the serpentine belt. Remove the two mounting bolts on the face of the alternator and the one behind the alternator. Remove the connections and alternator. To reinstall, reverse the process. You will not have enough clearance to remove the alternator without ratcheting the motor forward.

Posted on Nov 12, 2009

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4

Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

How to reset check engine light on 2000 olds silhouette

Use a code reader or disconnect the battery NEGATIVE (not the positive!) cable for 5 min's. The best way is the code reader as you will loose all learned programming in the engine control computer and this can cause idle problems. Autozone will do this for you free.

Dec 16, 2016 | 2000 Oldsmobile Silhouette

1 Answer

I have a 2002 Olds Silhouette that sat for 3 years. I tried to jump it with no battery. Not enough juice to get it started. I put a new battery in it and now I get no power anywhere.

Most common problem is bad connection at the battery, or battery cable end terminals, but yes, all cars I've worked on have fusible links, either near the battery or near the starter.

Oct 22, 2016 | 2002 Oldsmobile Silhouette

2 Answers

HOW TO TAKE OUT BATTERY 2003 OLDS SIL

Remove wiper assembly plastic cover. Then remove front bolt that holds the cross brace bar over the battery. Loosen the bolt at the other end of the brace bar and rotate brace bar from over the battery to a new location and proceed to remove the plastic battery hold down mount on bottom of battery.Disconnect the negative then positive battery cables from the battery then rotate battery up and out of compartment -- this is a very tight fit. It will come out and the clearance is very small. This is a neat challenge. Be sure to buy proper size battery for replacemeent

Read more: http://wiki.answers.com/Q/How_do_you_remove_a_battery_from_an_Oldsmobile_Silhouette#ixzz1noNX2HXJ

Feb 29, 2012 | Cars & Trucks

1 Answer

Where is the crank position sensor on the 2000 olds silhouette

Hello Cary.
Your Olds actually has two crank sensors.
Each one sends different information to the computer.
The 24x sensor...
Right side of the engine, at the end of the crankshaft, behind the harmonic balancer
And the 7x sensor is mounted at the rear of the engine just above the edge of the oil pan. This one is tricky to change. Difficult to access as you need to reach in between the trans output shaft and the engine block.
There is a small bolt that retains it but they stick in place by an "o" ring. Carefully turn and pry after removing the retainer bolt.
Hope this helps you with your repair.

Thank you for using FixYa
KL

Dec 13, 2010 | 2000 Oldsmobile Silhouette

1 Answer

Just Changed battery on my Olds Silhouette. Car cranks ok but does not start. What should I check? Thank you

1) Is the ignition circuit ON? (are you getting spark) 2) Is there fuel getting to the engine. 3) Is there air getting to the engine. 4) Is the engine getting the proper timing signals.

Nov 21, 2010 | 1996 Oldsmobile Silhouette

2 Answers

I need to replace a coil pack on my 2000 Olds Silhouette. I know I have to rotate the engine. But am unsure on how to do it correctly.

you do not have to rotate the engine to change the coil packs. just turn the van off and unplug the coil pack un bolt it and pull the spark plug wires off

Sep 08, 2010 | 2000 Oldsmobile Silhouette

2 Answers