Question about 2007 Chevrolet Trailblazer

Abslight stays on. How to fix? This is a2007trailblazer?

Larry english Dec 30, 2016

Help someone! Help someone!

1 Answer

Jeff Armer

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.
Chevrolet Master
15,575 Answers

First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Posted on Dec 30, 2016

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Abslight stays on. How to fix?

Have you recently had any work done to your vehicle, like tires or brakes? Possible a connector for the ABS wasn't re-hooked up. OR there's a short.

Dec 30, 2016 | 2007 Chevrolet Trailblazer

1 Answer

After replacing 4 brake pads , rotors and 2 front wheel bearings my brake light and ABSlight stays on

Check bearing connection,if you plug in right,#1 could bent pin is side,#2 broken wire check where loops wires!!!! #3 bad module.

Oct 04, 2015 | 2005 Nissan Murano

1 Answer

How do I switch off my ABS light on my audi a4

I presume you haven't switched off the ESP or anything on the dashboard? Light might be because there is a fault with ABS, so best take to a garage and get them to read off the fault code

Aug 26, 2014 | 2007 Audi A4 1.9

1 Answer

Abslight stay on nd emergency light stay on and service brake sysem on dash stayon

check your brake fluid level. most new cars have a sensor that makes the light come on when the level gets low. and on something of that vintage, that is probably a good indicator that your brakes are worn out.

Sep 28, 2013 | 2002 GMC Envoy

1 Answer

ABS light stays on after new pad install

The ABSlight has nothing to do with the brake pads. It comes on to tell you there is a problem with the ABS system. You best option is to have the ABS computer scanned for trouble codes. This will help narrow down the possibilities. Typical problems include bad speed sensors, bad wheel bearings, or broken exciter rings. If you had posted a Year, make, model, and engine size, I may have been able to help narrow down some possibilities and/or given some tips on what to check. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jan 22, 2012 | Cars & Trucks

1 Answer

I have a 97 chevy suburban1500 myabs and light is on as I excelerate my spedomiter is not working and its not changing gears sounds like trans is goin only when abslight is on when and light is off truck...

If your tack, odometer ,engine light is on and indicator light is not working then it could be the fuse for the ******.It could also be your ignition switch is not suppling power to that fuse.No power to that fuse or if its blown will cause truck to stay in 3rd gear which is like a safe mode for it.

Nov 04, 2011 | 1997 Chevrolet K1500

1 Answer

Abslight stays on no brake lights

Fuse 12 (10 Amps) may be burned out. Its located in "Junction Block". Losing
fuse 12 would kill the ABS systems and light the ABS dashboard light.

Fuse 11 (20 Amps) may be out. Its located in "Power Distribution Center". Losing fuse 11
would kill the brake lights, and light the ABS dashboard light. If fuse 11 is blown,
check your (3) brake light sockets for shorts of any type, or fuse 11 will just blow again.

Here's your ABS Indicator Light wiring diagram: