My 96 XJ6 hasn't been set up for a remote keyless entry .only 1 spot for the key drivers front side

No that will not work

Theft Deterrent Arm/Disarm Modes
Important: Although mode 2 provides increased security, the content theft deterrent system disarms only by pressing unlock on the keyless entry transmitter. This can pose a problem if the keyless entry transmitter is damaged, lost, or inoperative for any reason while you attempt to disarm the content theft deterrent system.
Mode 1: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter. The system does not arm when you lock the doors with a power door lock switch.

Mode 2: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the doors with the keyless entry transmitter. The system does not disarm when you unlock the doors with the key.

Mode 3: The system arms when you lock the doors using a power door lock switch or the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter.
Changing the Feature Customization Modes

1. Turn off the IP dimmer switch.
2. Turn the ignition switch to the LOCK position.
3. Remove the BCM PRGRM fuse.
4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.
The BCM flashes the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode 4 repeats the sequence starting with mode 1.

6. Complete the following steps in order to change the theft deterrent arm/disarm mode:

6.1.
Insert the key in the left front, right front, or liftgate door lock cylinder.

6.2.
Rotate the key from the center to the unlock position.

6.3.
Press the horn button on the remote keyless entry transmitter.

6.4.
Count the number of chimes that you hear. The number of chimes tells you which mode you have set.

6.5.
Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates the mode that you want.

6.6.
Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:

1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.

If you are unable to change locking modes Theft Deterrent System Feature Customization Inoperative

yes it needs the fob, Keyless Entry Remote Fob Clicker for 2002 Mazda Protege5 With Do It...



2002 Mazda Protg Keyless Remote Key Fob
http://www.fobkeyless.com/2002-mazda-protege-keys-remotes-replacement.html

All BNW's have remote key openers built into key, so what doesn't work, the manual lock, or the remote key, or both. When you say you don't have keyless entry, on a BMW the remote is the key.
CeraCoat-NanoTech.com

hi
Chance are the driver side control module is not working.
Open the driver side, inner door panel and check

Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

sounds like the main acculator in the drivers door has gone bad have it replaced it should solve your problem.

check your fuses its locate under the driver side under the steering column.

need to remove door panel either the linkage clip either broke or disconnected --if have remote start on fob need dealer to program--if normal try these links
Lexus Free Keyless Remote Fob Entry programming instructions Free Keyless Remote Fob Entry programming instructions procedures for all...

Doubt its a fuse. Most likely the key pad has failed and needs to be replaced. On the bright side this is a good problem to have and you have a very reliable car.