Question about Cars & Trucks

1 Answer

Astrostart RS-613 will only work when my key is in the ignition. Any ideas?

Posted by Brian on

Ad

1 Answer

twormed

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 131 Answers
Ad

1 Related Answer

Bill Boyd

  • 53814 Answers

SOURCE: My astrostart system will only start my truck with

take the key and the vehicle to a service dealer as sometimes it is necessary to have the key reprogrammed to the immobiliser in the CPU program

Posted on Nov 14, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I connect a astrostart remote key to my '08 Chevy uplander?


you need to notify astrostart since their are 4 different types of systems and give them the information on all the specs for your vehicle and they will advise how much and what additional components are needed

Jun 29, 2016 | 2008 Chevrolet Uplander

1 Answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission


[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Nov 24, 2015 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

My astrostart system will only start my truck with a key in the ignition. The batteries in the fob had gone dead and when I replaced them, it did not start at all. I went through the reprogram process...


take the key and the vehicle to a service dealer as sometimes it is necessary to have the key reprogrammed to the immobiliser in the CPU program

Nov 14, 2014 | Cars & Trucks

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

Trouble shooting astrostart remote starter for hst 5224 model


Leave the ignition key on for 10 minutes until the security light goes off. You may have to do this three times for a 30-minute total for a relearn procedure

Nov 20, 2017 | Cars & Trucks

1 Answer

Ford focus rs alarm trouble


if its a factory alarm you put the key in and quickly turn the key on and of i cant remember if its 8 or 9 times but the horn will chirp then you push the lock and unlock on the fob the locks should respond then turn key off and your done. note that if you have more than one fob you have to press lock and unlock on all of them before you turn the key off and i believe you only have about fifteen seconds to do so if not let me know i will look it up at work

Sep 13, 2009 | Ford Taurus Cars & Trucks

1 Answer

2001 Sable Ignition - Key will NOT turn the cylinder.


Try turning the steering wheel with your left handle(to get pressure off of the lock) while trying to turn the key with your right hand.

Feb 08, 2009 | 2001 Mercury Sable

1 Answer

1991 cavalier 3.1 RS ignition starts in on position radio and wipers on and off ?


sounds like the ignition itself is worn,go get one from a scrap yard and replace it

Jan 25, 2009 | 1990 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...