Question about 2002 Jeep Wrangler

Open Question

Where is camshaft sensor located on 2002 jeep wrangler 4.0

Posted by Frank D Curtis on

Ad

5 Related Answers

Bill Hackett

  • 383 Answers

SOURCE: jeep wrangelr Crank Position Sensor

wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

Posted on May 10, 2009

Ad
mikestoys32

mikestoys32

  • 37 Answers

SOURCE: Jeep is giving a code of p0340 which is telling me

go to autozones website they have free diagrams

Posted on Dec 02, 2009

Ad

Anonymous

  • 71 Answers

SOURCE: where is locate the camshaft position sensor on

The camshaft position sensor is located inside the distributor. It is a hall effect swich, simply remove the distributor cap and the rotor and you can lift it out, unplug and replace.
Have fun but beware a bad crankshaft position sensor can cause a false cam sensor code to be set sometimes.
Good luck.

Posted on Dec 05, 2009

Richard Scordino

  • 6982 Answers

SOURCE: Where is the camshaft sensor located on my 99 Jeep Grand Cherokee

If you still have a cap rotor and ignition wires, it's inside the distributor. If not, it is the part where the distributor used to be (center rear of the engine behind the intake manifold)

Posted on Feb 19, 2010

emissionwiz

Marvin

  • 85239 Answers

SOURCE: where is the camshaft position sensor located on a

the camshaft position sensor is inside the distributor, the crank sensor is at rear of engine in bell housing above starter. see pic of sensor below


4912fd8.jpg

Posted on Jul 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is location of 2002 jeep wrangler fuse panel


It should be behind the glove box door.

Feb 09, 2015 | 2002 Jeep Wrangler

1 Answer

How to replace a camshaft position sensor 1995 jeep wrangler, 6 cyl, 5 speed stick


Remove the distributor cap and rotor, lift the sensor out and drop in the new one.

Aug 16, 2013 | 1995 Jeep Wrangler

1 Answer

1997 jeep wrangler has a long start. I have changed the fuel pump, camshaft sensor. any other suggestions


There is a head temp sensor and intake air temp sensor, either of which could make the mixture too lean. Check them with an ohmmeter. Not sure the exact reading, but bad ones usually go 0 or infinite.

Apr 08, 2011 | 1997 Jeep Wrangler

1 Answer

Will a faulty camshaft position sensor cut power to the fuel pump on a 1998 jeep wrangler?


If the computer does not see a signal from the crank sensor and the cam sensor it will not turn the asd relay on.
Best to test before buying either as other problems may exist. Chlton or haynes manuals are helpful and not expensive..

Jan 31, 2011 | 1998 Jeep Wrangler

1 Answer

I need to replace the cam sensor on my 97 jeep wrangler were do i find it in the motor..


For 1997 Jeep Wrangler 4WD 4.0L MFI 6cyl the Camshaft Position Sensor is located: Under hood, passenger side, front engine area, mounted on front of intake manifold

Hope helps (remember to rate this).

Oct 12, 2010 | 1997 Jeep Wrangler

1 Answer

Where exactly is the Oil Pressure Sending Unit on a Jeep Wrangler 2000 6cyl so i can replace?


Oil Pressure Sensor The 3 wire, solid-state engine oil pressure sensor (sending unit) is located in an engine oil pressure gallery.

Aug 07, 2010 | 2002 Jeep Wrangler

1 Answer

Where is the camshaft sensor located on 2002 jeep laredo 4.0 engine


most likely at the front of the engine above the water pump, directly over the camshaft.

Apr 30, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Anyone know where the engine number is on a jeep wrangler 2002


2002 Jeep Wrangler 4WD 2.5L SFI 4cyl

bce93b5.jpg

Fig. The engine serial number is located at the right front side of the engine block (models 1997-2005)

I hope help you wth this; good luck (remember rated this help).


Sep 24, 2009 | 2002 Jeep Wrangler

1 Answer

2007 Jeep Wrangler Unlimited Sahara


SUBJECT:
Long Crank Time Due To Possible Contact Of Camshaft Sensor To Camshaft Gear
OVERVIEW:
This bulletin involves the replacement of the engine camshaft sensor.
MODELS:
2007 (JK) Wrangler
NOTE: This bulletin applies to vehicles equipped with a 3.8L engine (sales code
EGT).
SYMPTOM/CONDITION:
The customer may experience one of the following conditions:
a). Long engine crank time.
b). Two engine start attempts prior to engine starting.
c). Due to the “TIP Start Feature” on automatic transmission equipped vehicles, once the
ignition key / switch has been released from the “START” position, the starter may stay
engaged for up to 10 seconds while the engine attempts to start.
The above conditions may be due to the position of the camshaft sensor to the camshaft
gear. The sensor spacer gasket may have come loose during engine assembly and
caused the camshaft sensor to be adjusted too close or in contact with the camshaft gear.
DIAGNOSIS:
If the above condition is present perform the Repair Procedure.
PARTS REQUIRED:
Qty. Part No. Description
1 04686353 Sensor, Camshaft

Jul 12, 2009 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

Engine ligth on .dianosed to be camshaft senor


The camshaft sensor is located inside the engine behind the valve covers. Usually a magnet with a single wire or set of wires. You will have to bring the car into a shop in order to have this properly fixed.
Please let me know if this helps.

Feb 11, 2009 | 2006 Ford Fusion

Not finding what you are looking for?
2002 Jeep Wrangler Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...