Cars & Trucks Logo

Related Topics:

R
Rene Hernandez Posted on Nov 03, 2016
Be the first to answer

What size bolts are used for the 2007 accent torque converter to flexplate?

Answer This Question

5 Related Answers

Anonymous

  • 60 Answers
  • Posted on Nov 23, 2008

SOURCE: 1995 Mitsubishi Mirage breaking flexplates

the dish in the center of the flexplate should protrude tword the engine, also check for excessive torque convertor run out, as that can crack the flexplate

Ad

Anonymous

  • 2004 Answers
  • Posted on Jun 05, 2009

SOURCE: I got a used transmission from a salavage yard

You gotta find the actual size. Return to store.

Anonymous

  • 174 Answers
  • Posted on Nov 11, 2009

SOURCE: Missing bolts on '73 superbeetle...

I wouldn't get them from the bolt store. Usually torque converter bolts have a special head on them. I would find a vintage beetle specialist online and get them from them. You could also buy an assortment of bolts to get the correct thread count and size found and then order torque converter bolts from a parts store. Oreilly's has some of the more standard converter bolts...

c17hydro

Greg Bernett

  • 2993 Answers
  • Posted on May 12, 2011

SOURCE: im looking for the specs

Please don't forget to rate! Thanks!

  • Transaxle mount and torque the bolts to 65-80 ft. lbs. (90-110 Nm)
  • Torque converter and torque the bolts to 34-39 ft. lbs. (46-53 Nm)
  • Flywheel cover and torque the bolts to 72-84 inch lbs. (8-10 Nm)

    • saailer

    David Burbee

    • 1871 Answers
    • Posted on Nov 07, 2011

    SOURCE: I have a 1991 Ford Mustang 2.3 litre LX Automatic.

    Hello! Your best bet is to visit your local Ford parts desk and have them order the correct hardware needed...guru...Saailer

    I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

    6ya.com

    Instant Repair Help over the Phone

    6ya.com

    Save Time & Money by instantly connecting to...

    Ad

    Add Your Answer

    ×

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    0helpful
    1answer

    Which bolts on first the transmission or torque converter on a 2000 ford ranger automatic
    Insert torque converter into transmission and hold in place with home made bracket. Move trans into position to engine while aligning the holes in the flexplate to the bolts in the torque converter. Once alignment, secure the transmission to the engine. Then tighten the converter nuts and bolts
    Read full answer
    Jan 16, 2020 • Ford Cars & Trucks
    0helpful
    1answer

    How do you remove the last two nuts or bolts located under the bell housing on a 1999 chevy astro van
    there are 6 bolts connecting the trany to the engine. They all should be easy to take out. Are you talking about the three nuts that are used to bolt the trany torque converter to the flexplate? If so, rotate the flexplate to reach the other 2 nuts.
    Read full answer
    Sep 09, 2018 • 1999 Chevrolet Astro
    0helpful
    1answer

    When putting a torque converter into a 92 GMC Suburban 1500 with a TH 700R-4 Tranny what would the torque pressure be?
    Torque converter to flexplate bolts = 46 ft.lbs.
    Read full answer
    Sep 25, 2015 • GMC Cars & Trucks
    2helpful
    2answers

    Took my 2004 Buick Ranier to garage said that the rattling noise was coming from the tork converter or fly wheel. What could that be
    Loose flywheel or torque mount bolts
    Read full answer
    May 31, 2015 • 2004 Buick Rainier
    0helpful
    1answer

    2001 tiburon
    Torque converters are bolted up to the flywheel or flexplate. Probably 4 or 6 bolts from the flywheel engine side into the torque converter.
    Read full answer
    May 03, 2012 • 2001 Hyundai Tiburon
    1helpful
    2answers

    BROKEN FLEXPLATE ON TOYOTA 4RUNNER HAVE BROKEN 3 IN LAST YEAR. THE BOLTS AROUND THE CRANK BREAK THE FLEXPLATE. WHAT CAN BE CAUSING IT.
    G'day mate , misallignment, make sure the bell housing is in good clean servicable condition also when the box is out check that the bell housing to gearbox is flat clean and serviceable by removing the torque converter and unbolting bell housing if it is posible also is the starter straight and in to the correct depth for mesh as if it is to shy or in to far it will put pressure on the flywheel as the torque converter has room to move in and out but the flywheel is under great pressure at that point and will not like being flexed bac to accomadate a deep starter, on the bell housing bolt holes there may be hollow dowels in the bolt holes make sure these are clean, in the right place and actually there,hope this helps
    Read full answer
    Apr 07, 2010 • 1997 Toyota 4Runner
    0helpful
    1answer

    Missing bolts on '73 superbeetle...
    I wouldn't get them from the bolt store. Usually torque converter bolts have a special head on them. I would find a vintage beetle specialist online and get them from them. You could also buy an assortment of bolts to get the correct thread count and size found and then order torque converter bolts from a parts store. Oreilly's has some of the more standard converter bolts...
    Read full answer
    Nov 11, 2009 • Volkswagen Beetle Cars & Trucks
    1helpful
    1answer

    I have removed the pressure plate and clutch disc. how do i remove the flex plate to get to the flex plate bolts. 2007 dodge ram 3500 6 speed manual transmission
    theres an access cover under the turbo on the front of the bellhousing (2 10mm bolts) that you have to remove to access the bolts that hold the flywheel to the flexplate. kinda like removing the bolts to a torque converter. flywheel is real hevy though, watch your fingers
    Read full answer
    Apr 27, 2009 • 2006 Dodge Ram 3500 Truck
    0helpful
    1answer

    1995 Mitsubishi Mirage breaking flexplates
    the dish in the center of the flexplate should protrude tword the engine, also check for excessive torque convertor run out, as that can crack the flexplate
    Read full answer
    Nov 10, 2008 • 1995 Mitsubishi Mirage
    0helpful
    1answer

    Im removing a auto tranny from a 2whl dr 1988 GMC jimmy. does the torque converter bolt to the flywheel.
    You'll have to remove the torque converter to flexplate bolts and push the converter back a little when you pull the trans. out.
    Read full answer
    Jul 28, 2008 • GMC Jimmy Cars & Trucks
    Not finding what you are looking for?

    View Most Popular

    Cars & Trucks

    Related Question

    Which bolts on first the transmission or torque converter on a 2000 ford ranger automatic

    • Ford Cars & Trucks

    48 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    New hyundai i30 has clock

    Hyundai Accent Cars & Trucks

    Radio Station Keeps Changing Automatically

    2006 Hyundai Accent

    With the ignition off, the rear tail lights won't turn off

    2000 Hyundai Accent

    Won't play just says 1CDE on screen

    2007 Hyundai Accent GS Hatchback

    What does ICDE mean on a Getz stereo MP3 player

    2007 Hyundai Accent GS Hatchback

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Hyundai Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Brad Brown

    Level 3 Expert

    19187 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    Direcci?n. user-manual-1997 Accent...

    1997 Hyundai Accent

    PDF Manual
    Http://www.inbusinesswindsor.com/2007I...

    2007 Hyundai Accent...

    PDF Manual
    Http://www.caaquebec.com/DocumentLibra...

    2006 Hyundai Accent

    Loading...