How to adjust the headlights on a mitsubitsi lancer 2005

If they are new they should work if not return them

On top of the headlight you will see screws marked with left or right and the other with high and low. Just turn the screws accordingly. Note it is marked as L R and H L

There are usually some adjustment/aligning bolts on the back of the headlight. You will have to park your car perpendicularly to a wall about 25 feet away from the car. Then you will adjust and align the bolts on the back. You will have to open the hood as the alignment bolts are on the back of the headlight which is accessible from the engine compartment side. There are usually 3 alignment bolts per headlight. You may have to chalk up a pattern on the wall when you do this. Here is one guide for you. http://www.popularmechanics.com/cars/how-to/repair/1347221

forums.evolutionm.net/lancer.../443432-lancer-factory-service-manuals-..

the OME sparkplug gap for lancer from factory
is ( 1.016 ) mm
use a tool named filler to adjust it

Open the hood, remove any panels covering the light, and unhook the wiring harness. The light is generally held in place with four screws or bolts. Remove them, but mark the allignment. The light pretty much just screws out.

_______________________
Audi-VW Airbag Reseter

Check the pump delivery pressure in the workshop. replace if pressure is low.

it sounds like you need a cam sensor

Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

1. Disconnect the negative battery cable. Remove the engine under cover.
   
2. Remove the crankshaft damper pulley.
   
3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
   
4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
   
5. Remove the auto tensioner. Remove the lower timing belt cover.
   
6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
   
7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.
   
   NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.
   
   
8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
   
9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
   
10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
    
11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
    
12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
    
13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.
    

Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

To install:



Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine



Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine



Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

There are adjusting screws on the top and side of each headlight. I like to get on a really dark road at night and set them to how I like them without blinding oncomming drivers. Good luck