Need torque setting for mahendra Scorpio 2.6 diesel turbo. Torque for conrod bolt and head bolt

no year told
no country told
what if they are TTY bolts so asking torque is dead wrong to ask
TTY are use once bolts.
the service manual covers all this why not buy that first.
and not do it all wrong.

Cylinder head

https://www.fixya.com/cars/t24149916-qr20de_cylinder_head_tightening_sequence

Page 96 for Nissan QR25DE

https://www.mahle-aftermarket.com/media/local-media-north-america/pdfs-&-thumbnails/torque3.pdf

https://www.google.com/search?q=2003+Nissan+Liberty+QR20+diesel%2C+bolt+torque+settings

...

Once you get the words in the right order to form the search query, you need to add the word of the part you want the torque setting for. The problem is the all the weighting is given to the torque that the engine produces and is normally right next to the horsepower

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+Torque+Settings

So insert 'wheel nuts', 'cylinder head' etc HERE

2017 Nissan Navara, 2.3 turbo diesel, HERE Torque Settings

Example for 'cylinder head'......

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+cylinder+head+Torque+Settings

..

https://www.fme-cat.com/CylinderHeadTorqueLookup.aspx

Check this manual

Search Results

F77 2.8 diesel non turbo.1989 model.require head bolt - Fixya

www.fixya.com/cars/t25792470-f77_2_8_diesel_non_turbo_1989
Jul 22, 2015 - f77 2.8 diesel non turbo.1989 model.require head bolt tensions,stages and sequence please - Daihatsu Rocky question. ... Torque to yeild bolts need to be replaced whenever the head comes off.....Long bolts are 46 ft lbs. and ...

Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

The torque settings for the cylinder head on a 2003 Ford Ranger 2.5 turbo diesel WLT engine are as follows:

• Main cap bolts: 70 Nm (52 ft-lbs)
• Head bolts: 65 Nm (48 ft-lbs)
• Rocker arm shaft nuts: 25 Nm (18 ft-lbs)

It is important to note that these torque values are for the cylinder head bolts and main cap bolts only. Other fasteners on the engine, such as the oil pan bolts, may have different torque requirements.
It is also important to use a torque wrench and follow the proper tightening sequence when installing the cylinder head. Consult the service manual for your vehicle or a repair manual for the specific tightening sequence and additional torque specifications.
I hope this information is helpful. If you have any further questions or need additional assistance, don't hesitate to ask.

Head bolt torque: 90-100 ft lbs., to be reached in 3 equal tightening steps, below is the sequence:
9 3 1 6 8
Front of vehicle
7 5 2 4 10

Main bearing cap torque: 75-85 ft lbs.
Rod bearing cap torque: 45-55 ft lbs.
Looks like u've been busy, and will be for a while. Good Luck!

Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees