How to remove 2012 ford focus steering rack

In the link

https://www.google.com/search?q=2012+Ford+focus+sel+fuel+filter+location

..

EVAP system may not be purging correctly.

put the key in and just jiggle the steering wheel while turning the key.

racket pion stiring is out replace it

There are few help links showing exact accurate procedure to replace Rack and Pinion. Click the link below and follow the procedure:-----
Pinion Seal Replace on Dodge Dakota? http://howtobyme.blogspot.in/2012/04/pinion-seal-replace-on-dodge-dakota.html

-----------

How to Replace a Rear Pinion Seal.
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html
------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

----------
How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

-----------
How to replace power rack and pinion steering gear on Toyota cruiser? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-rack-and-pinion.html

----------

How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html


------------
Front Drive Pinion Seal Removal on Ford Explorer? http://repairhelpcenter.blogspot.in/2012/03/front-drive-pinion-seal-removal-on-ford.html

-------------
How to Replace Driveshaft, Pinion Flange & Seal?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-driveshaft-pinion-flange.html

------------

How to Replace Power Rack & Pinion Steering Gear On 2007 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


----------
How to Remove Power Rack & Pinion Steering Gear on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-rack-pinion.html

-----------

Power Rack & Pinion Steering Gear replacing details for Buick Park Avenue and Pontiac Bonneville

http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

-------------

How to Replace Power Rack & Pinion Steering Gear on Mercedes Benz Truck? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


---------
How to replace Power Rack & Pinion Steering Gear on Toyota 4Runner? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion_27.html

-----------

Power Rack & Pinion Steering Gear Replacing on Toyota Land Cruiser & Sequoia? http://schematicsdiagram.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

----------
Power Rack & Pinion Steering Gear Removal on Toyota RAV4? http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear-removal.html

----------
How to Replace Power Rack & Pinion Steering Gear on Toyota Sienna? http://technoanswers.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html

------------
These details will help.
Thanks.

In relation to these problem there are few solved help links,i suggest you to go through the list and click the required link:-----

Power Steering going out? http://schematicsdiagram.blogspot.in/2012/04/power-steering-going-out.html

---------------
How to Replace power steering pump on Chevy silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html
--------------- How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html
------------- Power Recirculating Ball Steering Gear removal on Chevy silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/power-recirculating-ball-steering-gear.html
----------- Chevy Silverado 2500 HD steering wheel replacing Procedure? http://technoanswers.blogspot.in/2012/02/chevy-silverado-2500-hd-steering-wheel.html
----------- Steering Wheel Locked? http://schematicsdiagram.blogspot.com/2011/12/steering-wheel-locked.html

---------------
How to Remove Power steering Pressure Hose on Dodge Stratus http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

------------
How to replace power steering pump on Mitsubishi Diamante?

http://howtobyme.blogspot.com/2012/01/how-to-replace-power-steering-pump-on.html

---------------
How to bleed power steering pump on Toyota? http://repairhelpcenter.blogspot.in/2012/02/how-to-bleed-power-steering-pump-on.html

---------------

----------How to replace power steering pump on Toyota Land cruiser?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html

-----------
Steering service light ON GMC Sierra Denali?

http://technoanswers.blogspot.in/2012/02/steering-service-light-on-gmc-sierra.html

---------
Steering service light came on 2004 Pontiac Grand Prix

http://technoanswers.blogspot.in/2012/02/on-one-my-pontiac-grand-prix-relatred.html

----------
Check power steering message on Toyota?

http://schematicsdiagram.blogspot.in/2012/02/check-power-steering-message-on-toyota.html

-------
How to remove power steering pulley on 2002 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-steering-pulley-on.html
---------1992 Ford Aerostar Power steering and Alternator belt routing diagram? http://carbeltrouting.blogspot.com/2011/12/1992-ford-aerostar-power-steering-and.html

----------------
How to replace Power Steering Pump on Acura Car Models?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

--------------

How to replace Steering Linkage on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html

---------------
How to replace power steering pressure hose on mustang? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

-------------
STEERING SQUEAKS http://alltypesofpartsreplacing.blogspot.com/2012/10/steering-squeaks.html
----------- Steering Column Diagram For 1990 Jeep Wrangler http://schematicsdiagram.blogspot.in/2012/07/steering-column-diagram-for-1990-jeep.html
------------- How to replace Steering Wheel on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-wheel-on-acura.html

------------
How to replace Power Steering Pump on 1999 Acura TL?

http://howtobyme.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

-------------

These details will help.

Thanks.

if the rack and pinion was not leaking or causing problems. then he may of made a wrong move! if the rack was fine before, and you just lost power steering. then it is most likely the power steering pump or the lines that go from rack to the pump. good-day ! if a rack goes bad, you will get a bad steering problem or just bad steering.

YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE YOU HAVE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED.REMOVE FRONT WHEELS.REMOVE TIE RODS END COTTER PINS AND CASTLE NUTS.REMOVE TIE ROD ENDS FROM THE KNUCKLES.REMOVE FRONT STABILIZER BAR.POSITION THE DASH OPENING WEATHER SEAL FOR THE STEERING COLUMN OUT OF THE WAY.REMOVE OR DISCONNECT THE FOLLOWING.REMOVE PINCH BOLT RETAINING THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING.REMOVE STEERING GEAR RETAINING NUTS BOLTS.REMOVE REAR SUBFRAME BOLTS.USE WIRE TO SUPPORT EXHAUST COMPONENTS UNLESS YOU ARE REMOVING THEM COMPLETELY.SUPPORT THE EXHAUST SYSTEM FLEX TUBE AND REMOVE THE FLEX TUBE TO DUAL CONVERTER Y PIPE ATTACHMENT.LOWER THE VECHICLE SLIGHTLY UNTIL THE REAR SUBFRAME SEPARATES FROM THE BODY APPROXIMATELY 4 INCHES.REMOVE THE HEAT SHIELD BAND AND FOLD THE HEAT SHIELD DOWN.ROTATE THE RACK AND PINION ASSEMBLY TO CLEAR THE BOLTS FROM THE FRONT SUBFRAME AND PULL TOWARD THE DRIVERS SIDE OF THE VECHICLE.PLACE A DRAIN PAN UNDER THE VECHICLE AND DISCONNECT THE POWER STEERING LINES.REMOVE THE RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE***** TO INSTALL ****** INSTALL NEW TEFLON O - RINGS ON THE POWER STEERING LINE FITTINGS. PLACE THE RACK AND PINION RETAINING BOLTS IN THE GEAR HOUSING.INSTALL RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE.INSTALL POWER STEERING LINES ON THE RACK AND PINION ASSEMBLY. INSTALL RACK AND PINION ASSEMBLY ON THE SUBFRAME.INSTALL ******** HEAT SHIELD.INSTALL TIE ROD ENDS TO THE KNUCKLES TIGHTEN THE CASTLE NUTS AND INSTALL THE COTTER PINS.INSTALL STABILIZER BAR.INSTALL RACK AND PINION ASSEMBLY RETAINING BOLTS.TORQUE THEM TO 85 - 99 FT LBS. RAISE VECHICLE UNTIL SUBFRAME CONTACTS THE BODY.INSTALL REAR SUBFRAME RETAINING BOLTS TORQUE THEM TO 83 - 112 FT LBS.INSTALL EXHAUST SYSTEM FLEX TUBE TO DUAL CONVERTER Y PIPE.INSTALL FRONT WHEELS.INSTALL A NEW PINCH BOLT IN THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING ON THE RACK INPUT SHAFT TORQUE PINCH BOLT TO 25 - 33 FT LBS.POSITION THE STEERING COLUMN OPENING WEATHER SEAL OVER THE STEERING GEAR HOUSING.LOWER THE VECHICLE FILL THE POWER STEERING FLUID RESERVOIR. START THE VECHICLE AND CHECK FOR LEAKS. CHECK FOR PROPER WHEEL ALIGNMENT AND STEERING WHEEL POSITION.BLEED POWER STEERING SYSTEM.

cross member yes you do haveto remove it

you can buy remanufactured at parts store or buy used from car-part.com. page with * is lowest cost.

It's a pretty big job for a novice.

here's 96 taurus steps with 3.8l engine. don't have 94. should be similar

Removal
SPECIAL SERVICE TOOL(S) REQUIRED Tool Number Description T94T-6000-AH Exhaust Connector Holder Tool T57L-500-B Bench Mounted Holding Fixture

1. Disconnect negative battery cable.
   

1. Position steering wheel one-half turn to right and lock wheel.
   

1. Position steering column boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power steering short rack and separate.
   

1. Disconnect PCV vent tube and vacuum supply hose from clean air tube. Loosen two hose clamps retaining clean air tube and position out of the way.
   

1. Disconnect power steering auxiliary actuator and power steering pressure switch.
   

1. Remove two heat shield pushpin retainers from power steering hose bracket and remove heat shield.
   

1. Remove one retaining bolt from left turn pressure hose bracket.
   

1. Position drain pan under steering gear.
   

1. Remove power steering pressure and return hoses from fittings on power steering rack. Position both hoses out of the way. Disconnect rear HO2S connector at steering rack and position out of the way.
   

1. Partially raise vehicle.
   

1. Remove front wheel and tire assemblies.
   

1. Remove LH upper stabilizer bar link retaining nut and position link out of the way.
   

1. Loosen LH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
   

1. Loosen RH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
   

1. Raise vehicle.
   

1. Remove drain pan.
   

1. Remove two steering gear retaining nuts at front subframe.
   

1. Install Exhaust Connector Holder Tool T94T-6000-AH on flex tube.
   

1. Remove bolts, nuts, and gasket from where flex tube and converter Y-pipe connect. Separate tube from pipe.
   

1. Position Rotunda Power Train Lift 014-00765 or equivalent with wood blocks approximately 1016 mm (40 inches) in length (secured to lift) under subframe and raise.
   

1. Remove two rear subframe retaining bolts and lower subframe approximately 102 mm (4 inches).
   

1. Rotate power steering rack to clear bolts from subframe and remove assembly through LH wheel well.
   

1. Remove two bolts retaining power steering hose bracket to short rack and remove bracket.
   

1. Mount steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
   

1. Remove four clamps retaining bellows to steering gear and tie-rods. Remove bellows and power steering gear rack tube.
   

1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while loosening inner tie-rods. Remove tie-rods from steering rack. Remove steering rack from bench-mounted holding fixture.
   

Installation

1. Mount new steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
   

1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while tightening inner tie-rods. Tighten to 90-110 Nm (66-81 lb-ft).
   

1. Apply Steering Gear Grease C3AZ-19518-A meeting Ford specification ESB-M1C119-A to groove in connecting rods where tie-rod bellows clamp to front wheel spindle tie-rod and uniformly apply to inner diameter of bellows. Install bellows and gear rack tube onto short rack.
   

1. Install new inner and outer bellows clamps.
   

1. Remove steering gear from Bench Mounted Holding Fixture and place on bench.
   

1. Install power steering hose bracket and retaining bolts at top of steering gear. Tighten to 9-12 Nm (80-106 lb-in).
   

1. Install steering gear retaining bolts in steering gear housing and install short rack through LH wheel well.
   

1. Position steering rack and retaining bolts through subframe. Raise powertrain lift until rear subframe contacts body and install retaining bolts. Tighten to 135-195 Nm (100-144 lb-ft). Lower and remove powertrain lift from vehicle.
   

1. Install power steering short rack-to-subframe nuts. Tighten to 97-132 Nm (72-97 lb-ft).
   

1. Install new gasket, bolts and nuts at converter Y-pipe and flex tube. Tighten to 34-46 Nm (26-34 lb-ft).
   

1. Remove flex tube holder.
   

1. Partially lower vehicle.
   

1. Install LH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
   

1. Install LH stabilizer bar link and retaining nut. Tighten to 76.5-103.5 Nm (57-76 lb-ft).
   

1. Install RH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
   

1. Install tire and wheel assemblies. Tighten to 115-142 Nm (85-105 lb-ft).
   

1. Lower vehicle.
   

1. Remove old Teflon® O-rings from pressure and return hoses. Install new Teflon® O-rings on pressure and return hoses.
   

1. Install power steering pressure hose and return hose to fittings on power steering short rack. Tighten to 33-41 Nm (24-30 lb-ft).
   

1. Install one retaining bolt to left-turn pressure hose bracket. Tighten to 9-12 Nm (80-106 lb-in).
   

1. Connect rear HO2S connectors, power steering auxiliary actuator, and power steering pressure switch electrical connectors.
   

1. Position heat shield at power steering hose bracket and install pushpin retainers.
   

1. Install clean air tube, connect PCV vent tube and vacuum supply hose, and tighten hose clamps. Tighten to 2-3 Nm (18-27 lb-in).
   

1. Install steering column intermediate shaft coupling to power steering short rack and install pinch bolt. Tighten to 41-51 Nm (30-38 lb-ft). Position steering column boot over steering rack.
   

1. Fill and purge system.
   

1. Check operation.
   

1. Adjust only toe for alignment. Refer to Section 04-00 .