What are the torque specs for a 2000 ford ranger 4x4 front wheel hub

Question edited for clarity.
Question moved to model category.

2006 Toyota tundra 4.7L Front End Torque Specs

toyota-specs.com https://toyota-specs.com > cars > 2006 > tundra4.7 > t...
Toyota Tundra Front Axle Nut Torque Spec : 203 ft-lbs · Toyota Tundra Wheel Hub Torque Spec : 100 ft-lbs ...

BHA53102 Axle / Spindle Nut Torque Specification

1A Auto https://docs.1aauto.com > BHA53102 Torque S... PDF Toyota. 4Runner. 1996-02 4 Wheel Drive. Front. 174. 236. Toyota. Sequoia ... Tacoma. 2001-04 4 Wheel Drive. Front. 173. 235. Toyota. Tundra. 2000-06 4 Wheel ...
1 page
https://www.google.com/search?q=2006+Toyota+Tundra+4x4+front+axle+torque

..

The rod bearing cap bolt torque specifications for the 3.0L V6 engine in a 2000 Ford Ranger XLT 4x4 with a manual transmission are as follows:

• Step 1: Tighten the bolts to 15 foot-pounds of torque.
• Step 2: Tighten the bolts to 30 foot-pounds of torque.
• Step 3: Tighten the bolts an additional 90 degrees (1/4 turn) using a torque angle gauge.

It's important to follow the torque specifications and sequence in the manufacturer's service manual to ensure proper tightening and prevent damage to the engine.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

4 X 4 vehicles are only meant to be in 4 wheel drive on loose surfaces
on hard surfaces where the tires are not permitted to slip there is a torque wing up in the transmission , drive shafts and diffs
this results in hard gear shifting, noisy drive lines and early failures in drive shaft, diffs and transmissions
if you go far enough in reverse it will start to bind up again

ford ranger 1990
If you have trouble in fixing your vehicles, try this link. Very helpful

Here are the specs you're looking for:
• Font axle to hub nut torque 185 ft-lbs
• Front hub bearing bolts 60 ft-lbs
• Caliper housing bolts 125 ft-lbs
• Caliper guide bolts 26 ft-lbs
• front spindle hub nut 97 ft-lbs
• lug nuts 100 ft-lbs.

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80c90e49

Those vehicles should have a hub assembly which incorporates a bearing and hub in one unit. To my knowledge the bearing is not serviceable. The hub assembly is bolted to the steering knuckle, so there actually is no wheel bearing torque. The tire/wheel assembly bolts directly to the wheel flange on the new hub assembly.

the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

check the cv joint